User manual ALPINE TME-M680

[. . . ] Colombo 8, 20090 Trezzano Sul Naviglio MI, Italy Tel. : 02-48 47 81 ALPINE ELECTRONICS (BENELUX) GmbH Leuvensesteenweg 510-B6, 1930 Zaventem, Belgium Tel. : 02-725 1315 ALPINE ELECTRONICS FRANCE S. A. R. L. 50016 F-95945, Roissy, Charles De Gaulle Cedex, France Tel. : 01-48 63 89 89 ALPINE ELECTRONICS OF U. K. , LTD. 133, Spain Tel. : 34-45-283588 SE ENGLISH Contents Operating Instructions WARNING WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation and Connections Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · If properly connected, the monitors main POWER will turn off when the vehicle's ignition switch is off. After turning the system off, a slight ghost of the image will remain temporarily. Under cold temperature conditions, the screen may lose contrast temporarily. After a short warm-up period, it will return to normal. · · Adjusting the Volume 1 Adjust the volume level by pressing the button. or 4-EN Switching the display mode Adjusting 1 Press the DISP button. Each press of the button will cycle through the modes as follows. WIDE NORMAL ZOOM 1 2 Press and hold the DISP button for at least 2 seconds. (downward) : Adjusts. WIDE Normal images are expanded uniformly in the horizontal direction and are displayed over the entire screen. Normal image (4:3) 1 Brightness adjustment (BRIGHT) SETUP MENU 12 NORMAL ZOOM Normal images are expanded in the horizontal direction and are displayed over the entire screen. The expansion ratio increases towards the right and left edges of the screen. Allows the brightness (0 to 32) of the picture 2 Contrast adjustment (CONTRAST) SETUP MENU 16 Contrast can be adjusted from 0 to 32 3 Color depth adjustment (COLOR) SETUP MENU 32 Color depth can be adjusted from 0 to 32 5-EN Basic Operation 4 Dimmer adjustment (DIMMER) SETUP MENU Other Useful Feature Remote Control Sensor 10 The backlighting is set to the value adjusted at 0~10 5 IR-TX adjustment (IR-TX) SETUP MENU Remote sensor · Receives the remote control signal from connected ALPINE products such as DVD players and TV tuners. ON OFF ON : Enable to use IR Headphone 6 Reset or to restore system setting to Press factory detault. 7 Exit Select EXIT to exit setup menu, and the screen will return to normal mode. 3 After completing adjustments, press and hold the DISP button for at least 2 seconds. The screen will return to the normal mode. · If no operation is made for 5 seconds after selecting a mode to be adjusted, the adjustment mode will be cleared. 6-EN Information In Case of Difficulty If you encounter a problem, please review the items in the following checklist. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. Information Specifications MONITOR 5. 8" Low reflection rear projection type TN liquid crystal panel Drive System Active matrix drive, normally white display Number of Picture Elements 400(W) x 234(H) x 3 Effective Number of Picture Elements 99. 99% or more Light Source Internal optical system (U-type cold cathode fluorescent tube) Dimensions (W x H x D) 153 x 102 x 20mm Weight 255g Screen Size Display System No function or display. · Car's ignition is off. - Check the voltage of vehicle's battery. Black box Dimensions (W x H x D) Weight 177 x 103 x 28 mm 400g No picture display. · Brightness control is set for minimum brightness control. - Wait until the temperature inside the vehicle comes down to the operating temperature range (45°C). · Incorrect or open connection with the Monitor, AV interface unit. · Due to continuous product improvement, specifications and design are subject to change without notice. · The LCD panel is manufactured using an extremely high precision manufacturing technology. This means that there is a possibility that 0. 01% of the pixels could be either always ON or OFF. Picture color is poor. · Brightness/Color/Tint control are not set to the proper positions. - Check each control. Spots or dotted lines/stripes appear. · Caused by neon signs, high-voltage power lines, CB transmitter, other vehicle's ignition plugs, etc. - Change the location of your vehicle. Unit does not operate. · Monitor's power is not turned on. - Turn on the monitor's power. 7-EN Installation and Connections Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use. DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. Warning MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage. DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG. If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries. USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure. ) Failure to do so may result in fire, etc. BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. Failure to do so may result in electric shock or injury due to electrical shorts. Caution HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done. DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. [. . . ] Video input / output connector (AUX 3) Use this connector to input the video signals from a DVD player, TV tuner etc. AUX3 SELECTION S/W "OUT" position Audio input / output connectors Use these connectors to output the audio signals to other products. Video input / output connector Use this connector to output the video signals to other products. · Locate the unit and route the leads at least 10 cm away from the car harness. [. . . ]