User manual ALPINE TDM-9505RB

[. . . ] R TDM-9505RB TDM-9503R TDM-9501RM TDM-9501R FM/MW/LW/RDS Cassette Receiver · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] The display shows "PAUSE. " Press again to resume the tape playback. Press the Eject (c) button to stop the tape play and eject the cassette. The tape-direction indicator disappears. When the cassette is loaded, the player automatically starts tape playback and indicates "TAPE" in the display. Dolby B NR (Noise Reduction) (TDM-9505RB/TDM-9503R only) 2 Press the Eject (c) button when you want to eject the cassette tape. 1 After inserting a Dolby B NR encoded tape, press the B NR button. The display shows the "B NR" The tape noise is reduced in the Dolby NR mode when a Dolby B NR encoded tape is played. Press the B NR button to cancel the Dolby NR mode. NOTES · When power is turned off or the front panel is removed, the full-logic mechanism will automatically switch to the PAUSE mode. This protects the tape from being deformed by the pinch-rollers if left for long periods. · Auto Metal When a metal cassette tape is inserted, the player automatically adjusts to the equalization for metal or any other high bias tape for optimum sound. Repeat Play 1 Press the (REPEAT) button to play back repeatedly the current programme being played. The "RPT" indicator appears and the programme will be played repeatedly. The "RPT" indicator disappears. Normal Play and Pause 1 Blank Skip (B. SKIP) Insert a cassette (or press the source button to switch from the tuner or CD Changer mode if a cassette is already inside the tape player). The display shows or " during tape playback to "TAPE" and " show the tape side being played. When the end of the tape is reached, the unit automatically stops and reverses the tape to play the other side of the tape. 1 Press the B. SKIP button during tape play to skip over blank portions of the tape lasting 15 seconds or longer, "B. S. " appears on the display. "B. S. " disappears from the display. 11-EN Cassette Player Operation PROG P. S. DN P. S. UP g f (SCAN) Fast Forward and Rewind Programme Sensor (P. S. ) 1 Press the g or f button during tape play to fast rewind or forward the tape respectively. The tape side indicator ( or ) blinks and >> or << moves indicating the direction of the tape. When the end of the tape is reached in the rewind mode, the player stops automatically and begins playing from the beginning of the same side. When the end of the tape is reached in the fast forward mode, the player stops automatically and begins playing from the beginning of the opposite side. Press the f button during forwarding to stop fast forwarding and resume tape play. Press the g button during rewinding to stop rewinding and resume tape play. DN button once during tape play to return to the beginning of the current selection being played. If you wish to return to a selection further back, press repeatedly until the number of selections you would like to skip is shown in the display. The display will show PS-1 with the first press and will increase by one with each successive press up to PS-9. UP button once during tape play to advance to the beginning of the next selection. If you wish to advance to a selection further ahead, press repeatedly until the number of selections you would like to skip is shown in the display. [. . . ] 3 Remote Turn-On Lead (Blue/White) Connect this lead to the remote turn-on lead of your amplifier or signal processor. 4 Power Antenna Lead (Blue) Connect this lead to the +B terminal of your power antenna, if applicable. NOTE This lead should be used only for controlling the vehicle's power antenna. Do not use this lead to turn on an amplifier or a signal processor, etc. p Remote Control Interface Connector (TDM-9505RB/TDM-9503R only) To remote control interface box. e DIN Extension Cable NOTE Older Alpine CD Changer came with standard, straight type DIN connectors. [. . . ]