User manual ALPINE NVE-N099P

[. . . ] DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc. If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries. [. . . ] Mount the aerial. Spanner Pencil and eraser Aerial 3 Park the vehicle in a safe and level location. 4 5 Apply the brake and remove the ignition key. Clean dust and oil at the mounting location and mount the aerial. Aerial Notes: · Mount the aerial on a flat plane of the dash board or rear tray. · Some thermal reflection type or thermal absorption type glass may interrupt high frequency waves. If reception is poor with the aerial installed inside the car, try to mount the aerial outside the car. 6 Routing the aerial cable. Route the cable using the provided cable clamps to take up the cable's slack. Use the waterproof pad when running the cable under the vehicle's rubber gasket. Attach the cable at several points using the remaining cable clamps. Notes: · The magnet of the aerial is very strong. Keep the magnet away from articles susceptible to magnetic fields such as credit cards, watches, etc. Reception sensitivity may be decreased. Water proof pad Cable clamp 5 2. Connections 1 Disconnect the battery (­) terminal. 4 Wrap electrical tape around end of leads not used. Note: Some vehicles contain a vehicle control computer etc. in this case, contents of the computer memory may be erased when the battery (­) lead is disconnected. 5 2 Cut terminal leads as required, and attach the solderless connectors to the leads. Note: For leads which need branching to the speed sensor, dimmer, parking brake, etc. , use the solderless connectors. Connect the battery (­) terminal and turn the ignition key to the ACC or ON position. Is the illumination turned on?) You can check the language selection menu with the monitor. (Refer to the Owner's Manual for details. ) Go to step 6 after checking is completed. ON Preparation Navigation side lead 6 1 Solderless connector (supplied with the unit) Vehicle lead Turn the ignition key to the OFF position to turn off the power after completion of the check. OFF Navigation side lead Stopper 7 Pull out the ignition key and remove the battery terminal (­) again to begin installation procedure. 2 Pliers 3 Connect the power lead to this unit. NVE-N099P Wiring Diagram With IVA-D300R/IVA-D300RB/ TME-M770 (Touch panel-compatible Alpine products) Battery Lead (Yellow) (5A) BATTERY ACC (Ignition) (Red) To the Acc power lead (5A) Ground (Black) Connect to a metal part of classis body with screw Dimmer In (Illumination) (+) (White/Blue) To the Illumination signal line Parking Brake (Yellow/Blue) To the parking brake signal line Reverse (+) (Orange/White) To reverse lights (+12V signal) SUBW. Speed Sensor (Green/White)*1 Connect to VSS (Digital or Analog 0V - 3V) To the vehicle speed pulse line Ai-NET R L PRE IN/OUT REAR FRONT POWER SUPPLY REMOTE IN / OUT EXT. OUT Mute (Pink/Skyblue) NAVIGATION IN DISPLAY OUT AV. SELECTOR GPS Aerial (Included) Use this to connect a device having the IN-INT function (-) output for Audio Mute CAMERA IN AUX OUT VIDEO (MONO) L AUDIO R AUX IN RADIO ANTENNA IN 13P RGB Extension Cable Included A 12345 Power Connector Pin Configuration TMC Antenna (Included)*2 6 7 8 9 10 Attach to a bare metal chassis part of your vehicle. 1 2 3 4 5 6 7 8 9 10 Ground (Black) ACC (Ignition) (Red) Mute (Pink/Skyblue) Open Open Battery (Yellow) Dimmer In (Illumination) (White/Blue) Speed Sensor (Green/White) Parking Brake (Yellow/Blue) Reverse (Orange/White) A 5 10 ANT. GPS POWER 1 6 System expansion ports *1 Improper connection of the speed pulse line may cause important safety features of the vehicle to fail (such as the brakes or air bags). We strongly recommend that the installation be performed by a trained, authorized Alpine dealer. *2 For further details about the installation of the TMC antenna, refer to "6. NVE-N099P Wiring Diagram With CVA-1004R/CVA-1003R Battery Lead (Yellow) (5A) BATTERY ACC (Ignition) (Red) To the Acc power lead (5A) Ground (Black) Connect to a metal part of classis body with screw Dimmer In (Illumination) (+) (White/Blue) To the Illumination signal line Parking Brake (Yellow/Blue) To the parking brake signal line Reverse (+) (Orange/White) To reverse lights (+12V signal) Speed Sensor (Green/White)*1 Connect to VSS (Digital or Analog 0V - 3V) To the vehicle speed pulse line Mute (Pink/Skyblue) GPS Aerial (Included) Use this to connect a device having the IN-INT function (-) output for Audio Mute 13P RGB Extension Cable Included A 12345 Power Connector Pin Configuration Ground (Black) ACC (Ignition) (Red) Mute (Pink/Skyblue) Open Open Battery (Yellow) Dimmer In (Illumination) (White/Blue) Speed Sensor (Green/White) Parking Brake (Yellow/Blue) Reverse (Orange/White) TMC Antenna (Included)*2 6 7 8 9 10 Attach to a bare metal chassis part of your vehicle. 1 2 3 4 5 6 7 8 9 10 A 5 10 ANT. GPS POWER 1 6 System expansion ports *1 Improper connection of the speed pulse line may cause important safety features of the vehicle to fail (such as the brakes or air bags). We strongly recommend that the installation be performed by a trained, authorized Alpine dealer. *2 For further details about the installation of the TMC antenna, refer to "6. GPS POWER 1 6 System expansion ports 10 *1 Improper connection of the speed pulse line may cause important safety features of the vehicle to fail (such as the brakes or air bags). [. . . ] When attaching the film, be sure to break any trapped air bubbles using the supplied work spatula. Wipe off the moisture with paper, etc. , being careful not to move the film antenna. · Keep the metallic part of the film antenna within 25 mm of the ceramic line when attaching. · Do not place the metallic part of film antenna on the ceramic line. 3 Installing the antenna cable Power connection · Attach the power connection to the antenna by aligning the two protrusions of the case with the 8 mark of the film. · Remove the clear sheet from the inner-facing side of film antenna and the moisture protection sheet on the metallic part of the film antenna. 1 2 3 4 5 To Antenna Receptacle 1 Film Antenna 2 Ground Connector Connect this lead to a good chassis ground on the vehicle. [. . . ]