User manual ALPINE NVE-N077PS

[. . . ] BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. Failure to do so may result in electric shock or injury due to electrical shorts. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, shift lever, brake pedals, etc. [. . . ] This may cause parts to become loose resulting in hazards or product failure. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure. Precautions IMPORTANT Please record the serial number of your unit in the space provided on the back cover of Owner's Manual and keep it as a permanent record. · For installation of the main unit, avoid areas with a high incidence of dust or moisture. Installing the unit in such locations may result in contamination of the DVD ROM making it unreadable. · Do not install the navigation system near a CD player that may interfere with GPS signal reception. · The optimum locations for installing the GPS aerial are: ­ on the dashboard where no metal piece (such as the defogger wire or aerial wire) is located on the windshield. · Route the Speed Pulse Sensor cable away from the audio cables in order to avoid picking up noises. 3 Contents PRECAUTIONS 1. NVE-N077PS Wiring Diagram With IVX-C806/IVA-C800R/ IVX-M706/IVA-M700R/CVA-1006R/CVA-1005R 3-3. Preparation 1 Check accessory parts. GPS aerial (5 m) Aerial mounting plate ×3 Cable clamp Parking brake aux. cord ×2 Solderless connector Remote control ×2 Remote control holder (2. 5 m) (4. 5 m) Power cables 1 Bracket 13P RGB extension cable (6 m) Extension cables 2 Floor base ×2 8 Wing nut (M6) ×4 3 Screw with double washer (M5 × 8) ×4 Battery (AAA) 5 Flanged self-tapping screw (M5 × 15) ×4 4 Hex bolt (M6 × 50) ×4 One each for left and right 6 Spring washer (M6) ×4 7 Flanged hex nut (M6) ×4 9 Velcro fastener ×2 !Velcro tape " Self-tapping screw (M3 × 12) ×4 2 Prepare tools and mounting information. Screwdriver Electrical tape Mounting the aerial inside the vehicle. Mount the aerial. Pliers Spanner Pencil and eraser Aerial 3 Park the vehicle in a safe and level location. Notes: · Mount the aerial on a flat plane of the dash board or rear tray. · Some thermal reflection type or thermal absorption type glass may interrupt high frequency waves. If reception is poor with the aerial installed inside the car, try to mount the aerial outside the car. 4 5 Apply the brake and remove the ignition key. Clean dust and oil at the mounting location and mount the aerial. Aerial 6 Routing the aerial cable. Route the cable using the provided cable clamps to take up the cable's slack. Use the waterproof pad when running the cable under the vehicle's rubber gasket. Attach the cable at several points using the remaining cable clamps. Notes: · The magnet of the aerial is very strong. Keep the magnet away from articles susceptible to magnetic fields such as credit cards, watches, etc. Reception sensitivity may be decreased. Water proof pad Cable clamp 5 2. Connections 1 Disconnect the battery (­) terminal. 4 Wrap electrical tape around end of leads not used. Note: Some vehicles contain a vehicle control computer etc. [. . . ] Warning: Do not damage pipe or wiring when drilling holes. Depending on the locations of the mounting screw holes, the mounting brackets (for the left and right) can be used on either side. (Bottom side) Continued to step 5 "Securing leads, etc. " 3 5 6 11 a When mounting with floor base brackets 3 1 Mount the brackets 1. Mount the brackets 1 at both sides of the unit with screws with double washer (M5×8) 3. Depending on the locations of the mounting screw holes, the mounting brackets (for the left and right) can be used on either side. Cut the carpet in "x" shape with a cutter and insert the floor bases 2 from under side of the carpet. 2 3 4 Mount the unit on the carpet with spring washers (M6) 6 and wing nuts (M6) 8. Continued to step 5 "Securing leads, etc. " 8 1 3 6 2 Determine mounting position of the floor bases 2 for placement under the carpet. [. . . ]