User manual ALPINE NVD-T334

[. . . ] FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/ SOLO PER L'UTILIZZO IN AUTOMOBILE/PARA USO EN AUTOMÓVILES/ALLEEN VOOR GEBRUIK IN DE WAGEN/ENDAST FÖR BILBRUK/KUN TIL BRUG I BILEN EN R SMART MAP PRO for Direction Guidance Carte Européenne Détaillée Pour Guidage Dynamique DE Euro Multi Map NVD-T334 FR Prog. 4. 00 IT OWNER'S MANUAL Please read before using this disc. MANUAL DE OPERACIÓN Lea este manual antes de utilizar este disco. ES BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch der Disc. GEBRUIKSAANWIJZING Lees de gebruiksaanwijzing zorgvuldig door alvorens u de disk in gebruik neemt. MODE D'EMPLOI Veuillez lire avant d'utiliser ce disque. ANVÄNDARHANDLEDNING Läs igenom handledningen innan du använder den här skivan. NL ISTRUZIONI PER L'USO Si prega di leggere prima di utilizzare il disco. BRUGERVEJLEDNING Læs venligst denne vejledning, for du tager denne DVD i brug. SE DK ENGLISH Precautions Important Information, Please Read Carefully Before Using This Product. This product is intended to safely provide turn by turn instruction to get you to a desired destination. Please read the following precautions to ensure that you use your navigation system correctly. L This product is not a substitute for your personal judgment. Any route suggestions made by the navigation system may never supersede any local traffic regulations or your personal judgment and/or knowledge of safe driving practices. [. . . ] Select "Local POI" from the "Destination" menu by moving the Flipper switch up or down. Select a desired category from the "Local POI" list and press the OK button or MODE knob to execute the selection. This section describes the procedure using "Restaurant" as an example. Select "Chinese" from the "Restaurant" list and press the OK button or MODE knob to execute the selection. The message appears and the system starts searching for POI within a 30 km radius of the vehicle. Select a desired local point and press the OK button or MODE knob to execute the selection. 5 5 6 7 The displayed screen changes. Select "Start Guidance" and press the OK button or MODE knob to execute the selection. Select a desired item from "Quick/Short/Alternative" by moving the Flipper switch up or down, and then press the OK button or MODE knob to execute the selection. 8 16-EN Adding Waypoints on the Route You can set up to 2 waypoints after the route search from your current location to your destination has been completed. Setting the Display for the Destination Time You can set the display for the destination time in order to anticipate your arrival time or estimated remaining time before arrival. 1 2 Find the waypoint by address, Local POIs, etc. Select "Add Way Point" and press the OK button or MODE knob to execute the selection. 1 2 3 Press the MENU button to display "NAV. Select "System Setup" from the "Navigation Setup" menu by moving the Flipper switch up or down. Time to Dest. " from the "System Setup" menu and press the OK button or MODE knob to execute the selection. Select "Arrival" or "Remaining" from the menu and press the OK button or MODE knob to execute the selection. : the anticipated arrival time will be set, and the indicator is shown in the guidance display. Remaining : the estimated remaining time will be set, and the indicator is displayed on the guidance display. Arrival 3 The displayed screen changes and the added waypoints are displayed. The route searching starts. 4 5 Note Before setting the point, you can move the location of the added waypoint by moving the cursor with the Flipper switch. Tips · After setting the waypoint, each time you move the Flipper switch up, the direction and distance to the waypoint, and the anticipated required time that you have set is displayed. (The required time is only displayed when you are driving with the route guidance. ) 6 To return to the previous screen, press the RTN button. MENU" screen, press the MENU button. · If "Arrival" is set in the "Setting the Display for the Destination Time" section (this page), the anticipated arrival time is displayed. 17-EN Route Setting/Route Editing 4 OK MODE Flipper switch The system starts to search for a new round-about route in the vicinity of the vehicle. Changing the Searching Conditions Use this when you want to change the route preference while you are driving receiving route guidance. (For example, if the route preference is set to "Quick", and you want to change to another route preference. ) MENU RTN 1 2 3 4 Press the MENU button to display "NAV. Select "Search Condition" from the "Edit Route" menu by moving the Flipper switch up or down. Set your preference (Quick, Short, Alternative) from the "Search Condition" menu. Checking the Route by List With this detailed list you can find the route, road name and the distance between the points. 1 2 3 4 After setting the route, press the MENU button to display "NAV. Select "Turn List" from the "Edit Route" menu by moving the Flipper switch up or down. [. . . ] · Movement on a ferry boat · Rotation of a parking lot turntable · Movement by tow truck Poor satellite configuration Measurement is 2 dimensional The disc is dirty. Cannot read disc is displayed for a certain operation. Move to a location where GPS satellite reception is easy. Clean the disc. Periodically clean the pickup lens. 30-EN If this Message Appears Various messages are displayed on the monitor screen during operation. In addition to the messages telling you the current status or providing guidance for the next operation, there are also the following error messages. [. . . ]