User manual ALPINE MRX-M110

[. . . ] HAVE TH wiring an and exper you purch USE SPEC SECUREL other tha not secure loose resu DO NOT BLOCK VENTS OR RADIATOR PANELS. Failure to make the proper connections may result in fire or product damage. ARRANG A SHARP moving p will preve through a insulation DO NOT I DUST. av moisture result in p 2 ALPINE MRX-M110/MRX-M55 68-23120Z17-A (EN/FR/ES) añol English DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. [. . . ] € If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise suppressors, contact them for further information. € Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information. f Grou Conne the ve check (–) te comp loops Minim MRXMRX- a Speaker Output Terminals The MRX-M110/MRX-M55 has one set of speaker outputs. Be sure to observe correct speaker output connections and polarity in relation to the other speakers in the system. Connect the positive output to the positive speaker terminal and the negative to negative. Do not connect the speaker (–) terminal to the vehicle’s chassis. NOTES: • Do not connect speaker leads together or to chassis ground. € Reversing subwoofer polarity may be desirable in some installations for optimum bass performance. G Spea These pream you s your h high NOTE • Use con • For Rem SEN SEN sou On in t 6 ALPINE MRX-M110/MRX-M55 68-23120Z17-A (EN/FR/ES) añol English b Fuse MRX-M110 . O) d Battery Lead (Sold Separately) Be sure to add an in-line fuse with the battery lead as close as possible to the battery’s positive (+) terminal. This fuse will protect your vehicle’s electrical system in case of a short circuit. Consult the table below for appropriate fuse value and minimum wire gauge requirement. 60 amp fuse, 8AWG/8mm2 e Remote Turn-On Lead (Sold Separately) Connect this lead to the remote turn-on (positive trigger, (+) 12V only) lead of your head unit. If a remote turn-on lead is not available, see Connection Checklist section on page 11 for alternative method. Note: If using speaker input level signal from the head unit, remote turn-on lead connection is not necessary due to automatic signal detection. F Ground Lead (Sold Separately) Connect this lead securely to a clean, bare metal spot on the vehicle’s chassis. Verify this point to be a true ground by checking for continuity between that point and the negative (–) terminal of the vehicle’s battery. Ground all your audio components to the same point on the chassis to prevent ground loops while keeping wire length as short as possible. Da del voces ltavoz al del nto de g Speaker Level Input Connector These input leads are for use with head units not equipped with preamp outputs. When not using the RCA Line Input connectors, you should connect these wires to the speaker output leads of your head unit. The MRX-M110/MRX-M55 accepts input from high power or standard power head units. [. . . ] However, all speaker input leads (FL/FR/RL/RR) may be connected to prevent zero output when the head unit fader is adjusted. 4V at <1% THD+N Ref: 10W into 4Ω Ref: 10W into 2Ω Ref: 300W into 4Ω THD+N Ref: 500W into 2Ω Ref: 600W into 4Ω Ref: 1000W into 2Ω IHF A-wtd + AES-17 Ref: 1W into 4Ω S/N Ratio IHF A-wtd + AES-17 Ref: Rated Power into 4Ω +0/-3dB Ref: 1W into 4Ω +0/-1dB Ref: 1W into 4Ω Ref: 10W into 4Ω at 100Hz RCA Input Ref: Rated Power into 4Ω Speaker Level Input Ref: Rated Power into 4Ω Variable LPF (-24dB/oct. ) Bass EQ variable (fc=50Hz) 650W RMS x 1 1100W RMS x 1 800W RMS x 1 ≤0, 004% ≤0, 01% ≤0, 04% ≤0, 06% 90dB MRX-M55 350W RMS x 1 550W RMS x 1 400W RMS x 1 ≤0, 004% ≤0, 01% ≤0, 04% ≤0, 06% 90dB ♦ IMPO This Amp the limits specificat generates installed a instructio SERIAL N INSTALL INSTALL PLACE O ♦ IMP Please re provided number ♦ For E Should yo store of p ♦ For C Customer packaged United St informati 117dB 114dB 117dB 114dB Frequency Response 5-400Hz 10-300Hz >1000 >10kΩ 0. 6kg Dimensions 0 à -12dB 340mm (13-3/8”) 280mm (11”) 58mm (2-1/4”) 230mm (9”) 3, 8kg 0 à -12dB 250mm (9-7/8”) 190mm (7-1/2”) 58mm (2-1/4”) 230mm (9”) 2, 6kg Transmisión de Salida de entrada Ch 1/2, con preamplificación búfer Nivel remoto* Atenuación lineal *Requiere RUX-KNOB opcional Generales Ancho Dimensiones Altura Profundidad Solo disipador térmico 4V max 4V max 0 a -12dB 340mm (13-3/8”) 280mm (11”) 58mm (2-1/4”) 230mm (9”) 3, 8kg 0 a -12dB 250mm (9-7/8”) 190mm (7-1/2”) 58mm (2-1/4”) 230mm (9”) 2, 6kg NOTE: Specifications and design are subject to change without notice. [. . . ]