User manual ALPINE MRV-F900

[. . . ] 4 Channel Power Amplifier MRV-F900 R 4 Channel Power Amplifier · OWNER'S MANUAL Please read before using this equipment. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. ESPAÑOL FRANÇAIS · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. ENGLISH MRV-F900 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire's insulation from being cut by the metal edge of the hole. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure. 5-EN Installation Due to the high power output of the MRV-F900, considerable heat is produced when the amplifier is in operation. For this reason, the amplifier should be mounted in a location which will allow for free circulation of air, such as inside the trunk. For alternate installation locations, please contact your authorized Alpine dealer. 1. Make sure there are no objects behind the surface that may become damaged during drilling. Position the MRV-F900 over the screw holes, and secure with four self-tapping screws. NOTE: To securely connect the ground lead, use an already installed screw on the metal part of the vehicle (marked (#)). Be sure this is a good ground by checking continuity to the battery (­) terminal. 1 Self-Tapping Screws (M4 x 20) 2 Ground Lead 3 Chassis 4 Holes 1 2 # 3 Fig. 1 4 6-EN Mounting the End Covers · The product's appearance can be improved by mounting the end covers on the main unit after installation. · Mount the end covers after installing the main unit. 1 Mounting the brackets 1) Use the included machine screws 6 to mount the three included brackets 5 onto the side opposite the terminal surface. 2 NOTE: APPLYING THE DOUBLE FACE TAPE Perform the procedure below when you want to securely fasten the end cover or when you do not plan on removing the cover once it is mounted. 1) Peel off the paper from one side of the included double face tape 7. 2) Apply one piece of double face tape 7 to the upper surface of the three brackets 5. 3 2 Applying the cushion 1) Peel off the paper from the included cushion 8. 4 3 Mounting the end covers 1) Mount the end covers 9 to the brackets 5. NOTE: To remove the bracket 5, push up vertically from the bottom upwards, in the opposite direction of when the bracket was installed. 9 5 Fig. NOTES: · Please make sure not to short the exposed connector to any grounded metal surface when replacing the fuse or making initial connection. · When adding a fuse to the battery lead, be sure to use the 80A fuse (supplied) with its fuse holder (supplied). · Do not place the fuse holder (supplied) in the vehicle's engine compartment because of the high temperatures reached in this area. · In order to protect the vehicle's battery and the wiring, be sure to use an equivalent replacement for the supplied (80A) fuse. [. . . ] Contact your authorized Alpine dealer. 14-EN Examples of System Expansion · SYSTEM A (4ch input, 4ch output) Battery Lead* 15 80A Ground Lead To the vehicle's battery SPEAKER L R SPEAKER L R NORMAL BRIDGED CH-1/ CH-2 ­ MODE NORMAL BRIDGED + ­ + ­ + ­ + CH-3/ CH-4 MODE BATTERY CH-1 GND RENOTE + BRIDGED + CH-1 ­ ­ + CH-2 ­ + BRIDGED + CH-3 ­ ­ + CH-4 ­ CH-3 INPUT SPEAKER OUTPUT CH-2 INPUT POWER SUPPLY SPEAKER OUTPUT CH-4 (L) (R) (L) (R) 14 14 (L) (R) (L) (R) Head Unit * NOTES: · Please make sure not to short the exposed connector to any grounded metal surface when replacing the fuse or making initial connection. · When adding a fuse to the battery lead, be sure to use the 80A fuse (supplied) with its fuse holder (supplied). · Do not place the fuse holder (supplied) in the vehicle's engine compartment because of the high temperatures reached in this area. · In order to protect the vehicle's battery and the wiring, be sure to use an equivalent replacement for the supplied (80A) fuse. [. . . ]