User manual ALPINE KTC-111TN INSTALLATION

[. . . ] 6-8 Fiveways Boulevarde Keysborough Victoria 3173, Australia Tel. : (03) 9769-0000 ALPINE ELECTRONICS GmbH Kreuzerkamp 7-11 40878 Ratingen, Germany Tel. : 02102-45 50 ALPINE ITALIA S. p. A. Via C. Colombo 8, 20090 Trezzano Sul Naviglio MI, Itary Tel. : 02-48 47 81 ALPINE ELECTRONICS FRANCE S. A. R. L. Paris Nord II B. P. 50016 F-95945, Roissy, Charles De Gaulle Cedex, France Tel. : 01-48 63 89 89 ALPINE ELECTRONICS OF U. K. , LTD. Tel. : 01908-61 15 56 INSTALLATION INSTRUCTION # ALA440089 KTC-111GY KTC-111TN Semi-Universal Trim Ring INSTALLATION MANUAL ALPINE ELECTRONICS DE ESPAN, S. A. [. . . ] INSTALLATION OF CONSOLE Caution: Use support for the console until secured to the vehicle. Failure to do so may cause damage to console or installed components. 2 19. The plain plastic trim ring may be painted or covered with material if desired. Additionally, the vinyl covered low profile trim ring my be dyed for color matching. Insert the LCD monitor into the trim ring and secure using screws provided with monitor. Install dome light switch (item 13 pg 3) in opening in front of console. 7 22. To determine the length of spacers (item 9 pg 3) and screws that will be needed, place a straight edge across the console and measure to each mounting boss as shown. Mark each spacer and screw appropriately, then trim to measured length. See Photo 8. 4 5 6 7 8 9 10 11 12 13 14 SPLIT LOCK WASHER, # 8 PUSH ON RETAINER FENDER WASHER NUT, 8-32, KEPS SCREW, 8-32 X 3 1/2" PPH PLASTIC SPACER, 1/4" X 1/2" X 3" MOUNTING BRAKET CONSOLE, VINYL COVERED CONSOLE, PLASTIC ONLY SWITCH, SPDT CONSOLE MOUNTING BRACKET 4 4 4 4 4 4 1 1 1 1 1 Caution: If screws extend more than 1" past the edge of console, PHOTO 7to roof of vehicle damage may occur. If spacers and screws are different lengths, be sure make note of proper location for correct installation. Install (4) four proper length 8-32 screws (item 3 or 8 pg 3), (4) four # 8 lock washers (item 4 PHOTO 8 pg 3), and (4) four plastic spacers (item 9 pg 3) previously cut. Place fender washer (item 6 pg 3) and push on retainer (item 5 pg 3) over screws as shown. PREPARATION OF VEHICLE INTERIOR MATERIALS PROVIDED FOR INSTALLATION: ITEM Description SCREW, 8-32 X 3/8" PPH 1 PHOTO 9 6 SCREW, #10 X 3/4" HWH SCREW, 8-32 X 1 1/2" PPH PHOTO 10 QTY 4 1. Determine which console is to be used, the low profile vinyl covered console (item 11 pg 3) for relatively flat headliners or high profile plastic only console (item 12 pg 3) for heavily contoured headliners. Insert the TMX-R680A LCD monitor in the console and secure using (4) four screws provided with monitor. 3 See Photo 1. 2 3 4 4 3. Determine a suitable mounting location by raising console into approximate position and checking the viewing angle from the rear seat, contours in headliner, that THE MONITOR CAN NOT BE VIEWED BY THE DRIVER, AND THAT THE MONITOR WILL NOT IMPROPERLY LIMIT REAR VIEW MIRROR FUNCTIONS. ENSURE COMPLIANCE WITH ALL APPLICABLE SAFETY STANDARDS GOVERNING THE FUNCTION OF THE REAR VIEW MIRROR, THE 12. Using an analog or digital multi-meter, test the function of the dome lights. Install and route all video and audio cables, and any other added component requirements to their respective places in the vehicle. The suggested routing of the video system cable is as follows: Above the headliner from video system to the B-pillar. [. . . ] Tape a pen or pencil to the handle of a screwdriver to make a contour marking tool. Make necessary adjustments to the mounting bracket assembly and install in vehicle. Make sure that bracket is centered left to right and secure using (4) four # 10 x 3/4" screws (item 2 pg 3). Prepare connection of the vehicle's dome light wires to the monitor for proper function. [. . . ]