User manual ALPINE IVA-D310R

[. . . ] FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE/PARA USO EN AUTOMÓVILES/SOLO PER L'UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK R Mobile Media Station EN IVA-D310R IVA-D310RB TM DE DIGITAL VIDEO FR · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] Connect the optical digital input connector with the connector for the DVD. OTHER: · Immediately after changing the settings of Display Mode (While the system is writing data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the settings may not be changed. Setting the Brightness of the Backlighting Backlighting is provided by a fluorescent light built into the liquid crystal panel. The illumination control adjusts the brightness of the backlighting based on the car ambient lighting for easier viewing. Setting item: DIMMER Setting content: OFF / ON / AUTO Deactivate Auto Dimmer mode to keep the background illumination of the monitor bright. AUTO: Adjust the brightness of the background illumination of the monitor automatically to the brightness of the car interior. OFF: · After input selection is completed, turn ignition OFF and back ON again. Your setting of the optical digital input switch is completed. Setting the Digital Output To connect an audio processor using the optical digital output, set to "ON" by the following procedure. Setting item: OPTICAL OUT Setting contents: OFF / ON · When ON or AUTO is set, the setting is also applied for the button lighting in "Adjusting the Dimmer of Button Lighting at Night" (page 33). · Afterwards, set ACC to OFF once, then turn it ON again. The setting of Digital Output is decided. 36-EN Adjusting the Minimum Level of Backlight You can adjust the brightness of the backlight (LOW). This function could be used, for instance, to change the screen brightness while travelling at night. Setting item: DIMMER LOW LEVEL Setting content: -15 to +15 Turning the Touch Panel Vibration ON or OFF You can turn the touch panel's vibration ON or OFF during operation. Setting item: PULSETOUCH Setting content: OFF / ON OFF: ON: Turns off vibration during operation. Turns on vibration during operation. You can adjust the level between MIN (-15) and MAX (+15). When it reaches the minimum or maximum point, the display shows "MIN" or "MAX" respectively. Adjusting the Touch Panel Adjustment becomes necessary when the display position on the LCD and the touch position on the touch panel do not match. Setting item: SCREEN ALIGNMENT Setting content: / RESET Switching Background Textures You have a choice of background textures you can set. Setting item: BACKGROUND Setting content: MODE1 / MODE2 · This operation can be carried out after removing the disc from the unit or when playback of the disc has stopped. · Wallpapers downloaded from "Downloading the MY BACKGROUND data" (page 45) are recalled. · When you select a source other than the built-in disc on this unit, and the built-in disc is selected on the rear monitor connected to the unit, background textures cannot be displayed on the unit. · When an error message is displayed (ERROR, HI-TEMP, etc. ), background textures selected by this setting cannot be displayed on the unit. 1 Touch [ ] of SCREEN ALIGNMENT. 2 Accurately touch the mark provided in the lower left corner of the screen. 3 Accurately touch the mark provided in the upper right corner of the screen. This completes adjustment, and returns to the DISPLAY setup mode screen. · If you have touched a location other than the mark, touch [RESET] to restore the adjustment screen to the initial setting. · If you touch [RETURN] on the adjustment screen, no adjustment is done and the DISPLAY setup screen is restored. Setting Automatic Background Textures The background texture will automatically change each time the ignition key is turned off and turned back on again. Setting item: AUTO BACKGROUND Setting content: OFF / ON ON: Turn on the Auto Background Texture Scroll mode. The background textures will scroll when the ignition key is turned off once and turned back on again as follows: MODE1 MODE2 OFF: Turn off the Auto Background Texture Scroll mode. · Wallpapers downloaded from "Downloading the MY BACKGROUND data" (page 45) are recalled. Setting the Font Type You can choose a character (text and tag information, etc. ) font type for the main display. Setting item: FONT TYPE Setting content: FONT 1 / FONT 2 FONT1: Selects bold characters. FONT2: Selects round characters. Switching the Font Back Display Colour You can choose from 5 different display colours for the font back (source title, shortcut display, etc. ). Setting item: BASE COLOR Setting contents: MODE 1 to MODE 5 37-EN i-PersonalizeTM Media Xpander Function Setting the MX mode The Parking Brake must be engaged to access the i-Personalize mode screen. Attempting to access this screen while driving will display the warning-CAN'T OPERATE WHILE DRIVING. [. . . ] Refer to "Setting the Digital Output" (page 36) and set to ON. Then refer to "Optical Digital Input Selection for an External Audio Processor" (page 36) and switch the setting. · * When connecting with PXA-H510 : - Connect the fiber digital input terminal to the DVD. - IVA-D310R/IVA-D310RB and DVA-5205P or DVA-5210 cannot be connected simultaneously when fiber digital is in use. [. . . ]