User manual ALPINE INA-N333R SOFTWARE

[. . . ] ENGLISH Precautions Important Information, Please Read Carefully Before Using This Product. This product is intended to safely provide turn by turn instruction to get you to a desired destination. Please read the following precautions to ensure that you use your navigation system correctly. L This product is not a substitute for your personal judgment. Any route suggestions made by the navigation system may never supersede any local traffic regulations or your personal judgment and/or knowledge of safe driving practices. Do not follow route suggestions if the navigation system instructs you to perform an unsafe or illegal manoeuvre, places you in an unsafe situation, or routes you into an area which you consider unsafe. [. . . ] Select a desired item from "Quick/Short/Alternative" by moving the Flipper switch up or down. The route guidance back to your home starts. MENU RTN Searching from Local Points You can search for POIs such as restaurants, hotels, etc. , within a 30 km radius of the present vehicle position. 4 1 2 3 4 Press the MENU button to display "NAV. MENU" by moving the Flipper switch up or down and press the OK button or MODE knob to execute the selection. Select "Local POI" from the "Destination" menu by moving the Flipper switch up or down. Select a desired category from the "Local POI" list and press the OK button or MODE knob to execute the selection. This section describes the procedure using "Restaurant" as an example. Select "Chinese" from the "Restaurant" list and press the OK button or MODE knob to execute the selection. The message appears and the system starts searching for POI within a 30 km radius of the vehicle. Select a desired local point and press the OK button or MODE knob to execute the selection. 5 5 6 7 The displayed screen changes. Select "Start Guidance" and press the OK button or MODE knob to execute the selection. Select a desired item from "Quick/Short/Alternative" by moving the Flipper switch up or down, and then press the OK button or MODE knob to execute the selection. 8 16-EN Adding Waypoints on the Route You can set up to 2 waypoints after the route search from your current location to your destination has been completed. Setting the Display for the Destination Time You can set the display for the destination time in order to anticipate your arrival time or estimated remaining time before arrival. 1 2 Find the waypoint by address, Local POIs, etc. Select "Add Way Point" and press the OK button or MODE knob to execute the selection. 1 2 3 Press the MENU button to display "NAV. Select "System Setup" from the "Navigation Setup" menu by moving the Flipper switch up or down. Time to Dest. " from the "System Setup" menu and press the OK button or MODE knob to execute the selection. Select "Arrival" or "Remaining" from the menu and press the OK button or MODE knob to execute the selection. : the anticipated arrival time will be set, and the indicator is shown in the guidance display. Remaining : the estimated remaining time will be set, and the indicator is displayed on the guidance display. Arrival 3 The displayed screen changes and the added waypoints are displayed. The route searching starts. 4 5 Note Before setting the point, you can move the location of the added waypoint by moving the cursor with the Flipper switch. Tips · After setting the waypoint, each time you move the Flipper switch up, the direction and distance to the waypoint, and the anticipated required time that you have set is displayed. (The required time is only displayed when you are driving with the route guidance. ) 6 To return to the previous screen, press the RTN button. MENU" screen, press the MENU button. · If "Arrival" is set in the "Setting the Display for the Destination Time" section (this page), the anticipated arrival time is displayed. 17-EN Route Setting/Route Editing 4 OK MODE Flipper switch The system starts to search for a new round-about route in the vicinity of the vehicle. Changing the Searching Conditions Use this when you want to change the route preference while you are driving receiving route guidance. (For example, if the route preference is set to "Quick", and you want to change to another route preference. ) MENU RTN 1 2 3 4 Press the MENU button to display "NAV. [. . . ] button This button is not used. Tips · · The Alpine head unit can be operated with the remote control. For details, refer to the INA-N333R/INA-N333RR or INA-N333RS/INA-N333RRS of Owner's Manual. After pressing the MODE button, press the following buttons while the status indicator is blinking : numerals (0 to 9), BS, and OK. Note Due to continuous product improvement, specifications are subject to change. 29-EN Reference In Case of Difficulty If you encounter a problem, please review the items in the following checklist. This guide will help you isolate the problem if the system is at fault. [. . . ]