User manual ALPINE EZI-DAB

[. . . ] Safety instructions WARNING Fit the unit and the antenna in a position that does not obscure the driver’s view. Do not fit the unit or the antenna in such a way that may interfere with the safe operation of the vehicle, the deployment of air bags or other safety equipment. Read this manual fully before operating the unit, including all safety notices. EN CAUTION Do not expose the unit to direct sunlight for long periods, for example, inside a hot car. [. . . ] EN Removing the controller Hold the bracket and pull the controller firmly up by the sides to remove it. If EZi-DAB is switched on when you remove the controller it will continue radio or track playback until you replace and stop playback, turn off EZi-DAB or turn off your ignition. English Deutsch Changing the display language Press SELECT to confirm Confirm restore defaults FM transmit frequency If your unit has been installed to use FM transmit or FM direct inject, you can change the frequency on which EZi-DAB transmits if you find it is interfering with a broadcast station. Turn the Select knob to choose a new transmit frequency and push the Select knob to confirm. 16 Package Contents • Controller • Main Unit (Interface) • Controller bracket with captive cable • Controller mount with adjustable angle • Wiring loom with ISO connectors • USB extension lead • 3. 5mm jack audio cable • Coaxial FM antenna loop through cable • Self adhesive controller bracket mounting pad • Owner’s manual Considerations before starting Minimum vehicle requirements • Fitted audio system including AUX-IN or FM antenna connection. EN Recommended for best results • Check that the latest version of software is installed. To find out which version your unit has installed: Press the button , Select Settings > Software update. Main unit (Interface) positioning Consider length of controller cable and USB/AUX audio extension and possible routing, whether access required to unit after fitting and distance from antenna and suitable power connection (avoid using safety critical power circuits such as airbag/ABS system etc). Controller positioning • Consider usability and visibility from driving seat, possible mounting points/brackets, cable length and routing to main unit. • Decide on connection to Head Unit – AUX IN or FM and whether FM pass-through is required. 17 Connections and System Wiring Diagram A EZi-DAB power connector pins Function Colour Purple Grey Brown Yellow Pink Red Orange Black B Pin 1 2 3 4 5 6 7 8 Nav_Tel_Audio+ Nav_Phone_Mute Cabin illumination 12V Permanent battery supply (with series fuse holder) Nav_Tel_Audio_GND 12V Switched ignition (with series fuse holder) Car mute (with crimp) Ground ISO connector pins Function Mute 1 (with crimp) Mute 2 (with crimp) Mute 3 (with crimp) 12V Switched ignition (with series fuse holder)* Not used Cabin illumination 12V Permanted battery supply (with series fuse holder)* Ground USB extension cable (supplied) 5 6 7 8 1 2 3 4 Mute AUX IN cable (3. 5mm) † FM loop-through cable (supplied) † Head Unit Black * On some vehicles switched and permanent live connections may be reversed. € If connected to Head Unit AUX IN then FM antenna connections to EZi-DAB are not required. KAE-220DA) or any active (powered) DAB antenna with 5V phantom feed and SMB (f) connector Please make sure ONLY to connect a dedicated 5V phantom supplied antenna. 18 Fit cables and connections EN Fit USB extension and AUX IN cables Route the USB extension (used for MP3/iPod connection) and AUX IN cable from e. Note that even if this cable is not required for use with music devices, it is recommended that it is installed to enable easy access to the USB socket for software updates. Fit connections to the Head Unit Slide out the Head Unit and connect AUX IN cable from EZi-DAB or connect the FM pass-through cable and reroute the existing FM antenna cable and the pass through cable to where you will fit the main unit. Note: If the Line out connection on EZi-DAB is used the FM transmit/pass through is disabled. Connect the power loom Connect the supplied loom to the vehicle’s system ensuring the EZi-DAB power connector is positioned where you will fit the main unit. Note: The supplied loom provides a permanent live and ignition controlled live feed to EZi-DAB but also offers other connections that may not be required. Run the cable for the controller from where you will fit the main unit to the desired mounting position e. [. . . ] IPod/USB: Tryk for at skifte indstillinger for vilkårlig afspilning af spor. Tryk på knappen, og hold den nede igen for at skifte indstillinger for gentagelse af spor. DK 5 Sådan kommer du i gang Tænd og sluk for enheden Tryk på knappen oven på controlleren for at tænde for EZi-DAB. Du skal blot tænde for EZi-DAB igen for at aktivere picnic-tilstand. [. . . ]