User manual ALPINE CVA-1006R

[. . . ] · ISTRUZIONI PER L'USO Si prega di leggere prima di utilizzare il attrezzatura. · ANVÄNDARHANDLEDNING Innan du använder utrustningen bör du läsa igenom denna användarhandledning. DE FR ES IT ALPINE ELECTRONICS, INC. Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel. : (03) 3494-1101 ALPINE ELECTRONICS OF AMERICA, INC. Tel. : 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. [. . . ] The selected disc number appears in the display and CD playback starts. NOTES · After selecting the desired disc, you can operate in the same way as for the CVA-1006R CD player. · When the "FUNC" indicator is lit in red in the monitor display, or is lit in the sub display, the disc select buttons become nonfunctional. When a 12-disc CD Changer is connected: To select discs numbered from 1 to 6, the procedure is the same as for the 6-disc CD Changer. In the sub display, this changes the "D" indicator to "d. " The "FUNC" indicator is lit in yellow on the monitor display. With the FUNC button activated, the Preset buttons 1 to 6 will represent discs 7 to 12 respectively. Controlling CD Changer An optional 6-disc or 12-disc CD Changer may be connected to the CVA-1006R if it is Ai-NET compatible. With a CD Changer connected to the Ai-NET input of the CVA-1006R, the CD Changer will be controllable from the CVA-1006R. Using the KCA-400C (the Multi-Changer Switching device) multiple changers can be controlled by the CVA-1006R. See the Multi-Changer Selection section on page 22 for selecting the CD Changers. NOTE The controls on the CVA-1006R for CD Changer operation are operative only when a CD Changer is connected. 1 Press the SOURCE button to activate the CD changer mode. The display shows the disc number and track number. NOTE The source indicator varies depending on the connected source. 21-EN CD Player/Changer Operation (Optional) BAND SOURCE Multi-Changer Selection Alpine's Ai-NET system will support up to 6 CD Changers. When operating two or more changers, the KCA-400C (Multi-Changer Switching device) must be used. If you use 2 Switching devices, you can connect up to 6 CD Changers. 3 The CD Changer Selection mode remains active for 3 seconds after step 2 is performed. Press the BAND button until the desired CD Changer indicator appears on the display. NOTE If the selected CD Changer is not connected, the display will show "NO CHANGER. " Alternatively press the BAND button on the Remote Control until the desired changer indicator appears on the display. 1 Press the SOURCE button on the CVA-1006R to activate the CD Changer mode. Release the button when you reach the desired portion you wish to play. Playback starts from that portion. 25-EN DVD/Video CD/CD Player Operation (Optional) SOURCE Disc Select buttons (1 through 6) RPT Repeat Play Controlling DVD Changer If an optional Alpine DVD Changer is connected to the CVA-1006R, the DVD Changer can be controlled from the CVA-1006R. 1 Press the RPT button during play to repeatedly play the chapter/track or title/disc being currently played. Each press changes the repeat play as follows: DVD: Title Repeat Off Chapter (repeat play) (repeat play) (normal play) 1 2 Press the SOURCE button. Press the Disc Select buttons (1 through 6) corresponding to one of the discs loaded in the DVD changer. Playback starts. NOTES · After selecting the desired disc, you can operate in the same way as for the DVD/Video CD/CD Player. · When the "FUNC" indicator is lit in red in the monitor display, or is lit in the sub display, the disc select buttons become nonfunctional. Video CD/CD: Track Disc Repeat Off (repeat play) (repeat play) (video CD only) NOTES · The track/disc repeat modes cannot be used on video CDs with playback control (PBC). When the monitor display is open: displayed in the monitor display · In case a 6-disc DVD changer is connected: In DVD changer mode, press the FUNC button to light in red the "FUNC" indicator and go to step 1. When the monitor display is closed: displayed in the sub display · In case a 6-disc DVD changer is connected: In DVD changer mode, press the FUNC button to illuminate the "FUNC" indicator and go to step 1. 26-EN Navigation System Operation (Optional) SOURCE Turning on the Navigation Mode If an optional Alpine Navigation System is connected, the display shows the navigation screen. 1 Press the SOURCE button to select the Navigation mode. NOTE If the Navigation mode does not appear in the display by pressing the SOURCE button, set the external setting of NAV. IN to ON (Refer to "Setting the External Input" on page 38). 27-EN Other Useful Features TITLE Displaying the Title/Text It is possible to display the CD title if the title has been previously inputted. You can display disc/track names during playback of CD text discs or MDs with input titles. CD changer mode: The monitor display is open. (displayed in the monitor display) ELAPSED TIME DISPLAY TEXT DISPLAY (DISC NAME)1 TEXT DISPLAY (TRACK NAME)1 TITLE DISPLAY2 1 In the MD/CD changer mode, press the TITLE button. "NO TEXT" will be displayed when the CD does not contain CD Text information. [. . . ] 7 Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+) 12V only when the ignition is turned on or in the accessory position. 8 Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided. 9 Power Antenna Lead (Blue) Connect this lead to the +B terminal of your power antenna, if applicable. NOTE This lead should be used only for controlling the vehicle's power antenna. [. . . ]