User manual ALPINE CDM-7858R

[. . . ] R CDM-7859R CDM-7858R CDM-7856R FM/MW/LW/RDS CD Receiver · OWNER'S MANUAL Please read before using this equipment. EN DE FR ES IT ALPINE ELECTRONICS, INC. Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel. : (03) 3494-1101 ALPINE ELECTRONICS OF AMERICA, INC. Tel. : 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. Markham, Ontario L3R 9Z6, Canada Tel. : 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF AUSTRALIA PTY. [. . . ] If the preset station's signal is weak, the unit automatically searches and tunes to a stronger station in the AF (Alternative Frequencies) list. If the preset station and the stations in the AF list cannot be received: Press the same preset button again within 5 seconds to have the unit search for a station in the PI (Programme Identification) list. If there are still no stations receivable in the area, the unit displays the frequency of the preset station and the preset indicator disappears. If the signal level of the Regional (Local) station being tuned becomes too weak to receive, press the same preset button to tune in a Regional station in other district. NOTE For presetting the RDS stations, refer to the Radio Operation section. The RDS stations can be preset in the F1 and F2 bands only. 1 2 3 Press the F button so that the F (Function) indicator lights up. Press the g DN or f UP button to tune in the desired RDS station. NOTE When the BAND button is pressed and held for more than 2 seconds while a station name is displayed, the display shows the station frequency for 5 seconds. 5 4 5 Press the AF button again to deactivate the RDS mode. The F indicator light goes out. Tips The RDS digital data includes the followings: PI Programme Identification PS Programme Service Name AF List of Alternative Frequencies TP Traffic Programme TA Traffic Announcement PTY Programme Type EON Enhanced Other Networks 10-EN Receiving RDS Regional (Local) Stations PTY (Programme Type) Tuning 1 2 3 4 Press and hold the SETUP button for at least 3 seconds to activate the setting mode. In the REG OFF mode, the unit automatically keeps receiving the related local RDS station. Press the SETUP button to deactivate the setting mode. 1 2 Press the F button so that the F (Function) indicator lights up. Press the PTY button to activate the PTY mode, while the unit is in Radio (FM receiving) mode. The Programme Type of the station being currently received will be displayed for 5 seconds. · If there is no receivable PTY broadcast, "NO PTY" will be displayed for 5 seconds. · If no RDS station can be received, the display shows "NO RDS. " NOTE If no button is pressed within 5 seconds after pressing the PTY button, the PTY mode will be automatically cancelled. Receiving Traffic Information 3 1 2 Press the T. INFO button repeatedly until the T. INFO indicator appears in the display. Press the g DN or f UP button to select your desired traffic information station. When a traffic information station is tuned in, the TP indicator lights up. If traffic information is not being broadcast, the unit is set in the standby mode. When a traffic information broadcast begins, the unit automatically receives it and the display shows "TRF-INFO" for a few seconds and returns to the PS display. When the traffic information broadcast is over, the unit will automatically set in the standby mode. NOTES · If the traffic information broadcast signal falls below a certain level, the unit remains in the receiving mode for 1 minute. If the signal remains below a certain level for over 1 minute, the "T. INFO" indicator blinks. · If you do not want to listen to the traffic information being received, lightly press the T. INFO button to skip that traffic information message. INFO mode will remain in the ON position to receive the next traffic information message. · If the volume level is changed while receiving traffic information, the changed volume level will be memorized. [. . . ] <JAPANESE CAR> Hex Nut (M5) Bolt Stud Front frame CDM-7859R/CDM-7858R/ CDM-7856R When your vehicle has the Bracket, mount the long hex bolt onto the rear panel of the CDM7859R/CDM-7858R/CDM-7856R and put the Rubber Cap on the hex bolt. If your vehicle does not have the Mounting Support, reinforce the head unit with the metal mounting strap (not supplied). Connect all the leads of the CDM7859R/CDM-7858R/CDM-7856R according to details described in the CONNECTIONS section. NOTE For the screw , provide a proper screw to the chassis installing location. CDM-7859R/CDM-7858R/ CDM-7856R Screws (M5 × 8) (Included) Mounting Bracket 19-EN Installation and Connections Connection Antenna 1 ISO Antenna Plug 2 (Pink/Black) (Blue/White) AUDIO INTERRUPT IN REMOTE TURN-ON To vehicle phone 3 To amplifier or equalizer (Red) IGNITION 4 5 6 8 9 To power antenna (Black) GND (Blue) POWER ANT Ignition Key 7 (Yellow) BATTERY Battery # A DIN Connector PIN Configuration lgnition Data Ground Lch ! " $ Shield Ground Power Supply Ground Battery Data Bus Rch A & Sig Gnd Speakers ) ~ + , . ( / : % Green Green/Black Rear Left White White/Black Grey/Black Grey Violet/Black Violet Front Left Front Right Rear Right CD changer (Sold separately) Speakers ; Amplifier (Sold Separately) Rear or Subwoofers For details on how to set the Subwoofer to ON/OFF, see "Subwoofer On and Off" on page 5. 20-EN 1 ISO Antenna Convertor Plug 2 Audio Interrupt In Lead (Pink/Black) Connect this lead to the Audio Interface output of a cellular phone which provides ground shorting when a call is received. [. . . ]