User manual ALPINE CDE-9882RI

[. . . ] FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/PARA USO EN AUTOMÓVILES/SOLO PER L'UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK/ALLEEN VOOR GEBRUIK IN DE AUTO/ /DO UYCIA TYLKO W SAMOCHODZIE/ EN R RDS MP3/WMA/AAC CD Receiver DE CDE-9880R/ CDE-9882Ri · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] Refer to "Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat" (page 15). *2 The function is inoperable when DEFEAT is set to ON. Setting the Bass Control You can change the Bass Frequency emphasis to create your own tonal preference. SOUND /ESC 1 2 Press SOUND to activate the Sound Setting mode. Turn the Rotary encoder to select the BASS Adjustment mode, and then press /ENT. SUBW LEVEL*3 SUBW LEVEL BASS*4 TREBLE*4 HPF*4 Adjusting Subwoofer Level/Bass Level/ Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/ Defeat Setting the Bass Centre Frequency 3-1 Press BAND/TA to select the desired bass centre frequency. 80 Hz 100 Hz 200 Hz 60 Hz 80 Hz 1 Press Rotary encoder (AUDIO) repeatedly to choose the desired mode. Each press changes the mode as follows: SUBW LEVEL* BASS LEVEL BALANCE FADER DEFEAT Subwoofer level : 0 ~ +15 Bass level: ­7 ~ +7 Treble level: ­7 ~ +7 Balance : L15 ~ R15 Fader : R15 ~ F15 Defeat : ON/OFF Volume : 0 ~ 35 TREBLE LEVEL VOLUME SUBW LEVEL Emphasizes the displayed bass frequency ranges. Setting the Bass Bandwidth 3-2 Press SOURCE/ bandwidth. to select the desired bass · If no operation is performed for 5 seconds after selecting the SUBW LEVEL, BASS LEVEL, TREBLE LEVEL, BALANCE, FADER or DEFEAT mode, the unit automatically returns to normal mode. * When the subwoofer mode is set to OFF, its level cannot be adjusted. Refer to "Turning Subwoofer ON/OFF" (page 16). Changes the boosted bass bandwidth to wide or narrow. A wider setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency. 2 Turn the Rotary encoder until the desired sound is obtained in each mode. By setting DEFEAT ON, previously adjusted settings of BASS and TREBLE will return to the factory defaults. Setting the Bass Level 3-3* Turn the Rotary encoder to select the desired 5 bass level (­7~+7). You can emphasize or weaken the bass level. Setting the Subwoofer Level You can change the Subwoofer Level to create your own tonal preference. 4 Press and hold /ESC for at least 2 seconds to return to normal mode. 1 2 3 Press SOUND to activate the Sound Setting mode. LEVEL Adjustment mode, and then press SUBW LEVEL*1 SUBW LEVEL BASS*2 TREBLE*2 HPF*2 · If no operation is performed for 15 seconds, the unit will return to normal mode automatically. · The bass level settings will be individually memorized for each source (FM, MW (LW), CD, etc. ) until the setting is changed. The bass frequency and bass bandwidth settings adjusted for one source are effective for all other sources (FM, MW (LW), CD etc. ). · When subwoofer is set to OFF and DEFEAT is set to ON, pressing the SOUND button momentarily will not be functional. *3 When the subwoofer mode is set to OFF, its level cannot be adjusted. 5 The adjustment can also be made by pressing Rotary encoder * (AUDIO). Refer to "Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat" (page 15). Turn the Rotary encoder to select the desired subwoofer level (0~+15). · If no operation is performed for 15 seconds, the unit will return to normal mode automatically. · When subwoofer is set to OFF and DEFEAT is set to ON, pressing the SOUND button momentarily will not be functional. 15-EN Setting the Treble Control You can change the Treble Frequency emphasis to create your own tonal preference. *9 When the subwoofer mode is set to OFF, its level cannot be adjusted. *10 The function is inoperable when DEFEAT is set to ON. 1 2 Turning Subwoofer ON/OFF When the subwoofer is on, you can adjust the subwoofer output level (refer to page 15). Press SOUND to activate the Sound Setting mode. Adjustment mode, and then press SUBW LEVEL*6 SUBW LEVEL BASS*7 TREBLE*7 HPF*7 1 2 3 4 Press and hold SOUND for at least 2 seconds to activate the Subwoofer selection mode. SUBWOOFER mode, and then press SUBWOOFER SUBW SYSTEM SUBWOOFER Setting the Treble Centre Frequency 3-1 Press BAND/TA to select the desired treble centre frequency. 10. 0 kHz 12. 5 kHz 15. 0 kHz 17. 5 kHz 10. 0 kHz Turn the Rotary encoder to select SUBW ON/OFF. SUBW ON (Initial Setting) SUBW OFF Emphasizes the displayed treble frequency ranges. Setting the Treble Level 3-2* Turn the Rotary encoder to select the desired 8 Press and hold /ESC for at least 2 seconds to return to normal mode. treble level (­7~+7). You can emphasize the treble level. · If no operation is performed for 15 seconds, the unit will return to normal mode automatically. 4 Press and hold /ESC for at least 2 seconds to return to normal mode. Setting the Subwoofer System When the subwoofer is on, you can select either SYS 1 or SYS 2 for the desired subwoofer effect. · If no operation is performed for 15 seconds, the unit will return to normal mode automatically. · The treble level settings will be individually memorized for each source (FM, MW (LW), CD, etc. ) until the setting is changed. The Treble frequency settings adjusted for one source are effective for all other sources (FM, MW (LW), CD, etc. ). · When subwoofer is set to OFF and DEFEAT is set to ON, pressing the SOUND button momentarily will not be functional. *6 When the subwoofer mode is set to OFF, its level cannot be adjusted. [. . . ] This can be done by pressing firmly in on the unit while pushing the locking pin down with a small screwdriver. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the detachable front panel. Lock Pin Pressure Plates* This unit Removal 1. Use a small screwdriver (or similar tool) to push the locking pins to the "up" position (see above drawing). [. . . ]