User manual ALPINE CDA-7893R

[. . . ] R CDA-7894RB CDA-7893R FM/MW/LW/RDS CD Receiver · OWNER'S MANUAL Please read before using this equipment. · BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. [. . . ] "PRIO-PTY" is displayed for 2 seconds and then the programme type for 3 seconds. The initial setting is "NEWS. " NOTES · If there is no receivable text message or the unit cannot receive a text message properly, the display shows "NO TEXT" for 2 seconds. · When the BAND button is pressed and held for at least 2 seconds while the PS (Programme Service Name) or Radio Text display is being displayed, the display shows the station frequency for 5 seconds, then returns to the previous display. NOTE If no buttons are pressed within 5 seconds after pressing the P. PTY button, the PRIORITY PTY mode is automatically cancelled. 3 4 Press the g DN or f UP button within 5 seconds while "NEWS" is being displayed to choose a desired programme type. PTY button for at least 2 seconds. NOTE In the PRIORITY PTY function, unlike in the T. INFO function, the volume does not increase during operation. 16-EN CD Player Operation -/J When a disc is already inserted, press the SOURCE button to switch to the CD mode. TUNER CD CD CHANGER ( Only when the CD changer is connected) 3 c To pause playback, press the -/J button. To eject the disc, press the c button. 4 NOTES · If the CD does not eject, press c button again for at least 3 seconds with the movable display open. · Do not insert or remove a CD when loading or ejecting a CD, as malfunction may result. Opening and Closing the Movable display 1 About the usable discs. We recommend using only compact discs containing the marks shown below. You can play CD-Rs (CD-Recordable)/CD-RWs (CDReWritable) for audio use on this unit. · Some of the following CDs may not play on this unit: Flawed CDs, CDs with fingerprints, CDs exposed to extreme temperatures or sunlight (e. g. , left in the car or this unit), CDs recorded under unstable conditions, CDs on which a recording failed and a re-recording was attempted. · Use discs with MP3 files written in the format compliant with ISO 9660 level 1 or level 2. The movable display will open. (Movable display fully opened) To close the movable display, press the c button again. The movable display will close. NOTES · Do not apply shock to the movable display when it is open as it may result in malfunction of the unit. · The display may be dim during low temperatures and immediately after turning on the power. · The display will stop at the set angle when closing. CAUTION Keep hands (or any other object) away from the display while it is opening or closing to avoid damage or injury. The back of the movable display will get very warm under normal operating conditions. Do not touch. On handling Compact Discs (CD/CD-R/ CD-RW) · Do not touch the surface. · Do not affix stickers or labels and do not write on the surface. Heat and humidity may damage the CD and you may not be able to play it again. Playback 1 Press the c button. The movable display will open. Insert a disc with the label side facing up. 2 To customers using CD-R/CD-RW Insert a disc with the label side facing up. · If a CD-R/CD-RW cannot be played back, make sure close session (finalization) has been performed. · Finalize the CD-R/CD-RW if necessary, and attempt playback again. 17-EN CD Player Operation M. I. X. [. . . ] This will enable the vehicle's dimmer control to dim the backlighting of the unit. 5 Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+) 12V only when the ignition is turned on or in the accessory position. 6 Power Antenna Lead (Blue) Connect this lead to the +B terminal of your power antenna, if applicable. # System Switch When connecting a processor using Ai-NET, place this switch in the EQ/DIV position. When no device is connected, leave the switch in the NORM position. NOTE Be sure to turn the power off to the unit before changing the switch position. $ % & ( ) ~ + , . [. . . ]