User manual ALINCO DJ-S1E

[. . . ] The manufacturer therefore accepts no liability for any damage arising from specifications that deviate from the standard version of the machine as delivered to you. Every possible care has been taken in the production of this document, but the manufacturer accepts no liability for any errors in this document or for any consequences arising therefrom. TAKE THE TIME TO CAREFULLY READ THIS DOCUMENT BEFORE USING THE MACHINE. ALWAYS KEEP THIS DOCUMENT NEAR THE MACHINE. PREFACE Using this document This document is intended to provide instructions for authorized users to safely install, use and maintain the machine. [. . . ] ­ Also this selected time setting has been protected, so that no one can cancel the setting between times, see the previous tip at § 7. 1. 1. ­ Permanent changing of the default settings is described in the extended programming mode § 7. 3. 18 version 1. 0 ECopyright Bravilor Bonamat B. V. 7. 2 The limited programming menu ­ Press the selection key (M. ) to counter­clockwise to the next setting (§ 7. 2. 2). By pressing a selection key several times, the entire carousel (fig. 12 ) can be gone through. ­ The settings are described in the order of the carousel, counter­clockwise (fig. 12 ). ­ With the red stop key (K. ) the programming can always be interrupted and stopped. ­ When nothing happens in the programming menu for 20 seconds, the programme returns to the users' menu (§ 7. 1). ­ When the symbol appears in the menu, the setting can be set to zero by simultaneously pressing both selection keys (M. ) and (N. ). Even if the amount at § 7. 3. 1 has been set in cups, jugs or us­gallons. GB Below a description is given of how operators with limited authority, after having entered the operators' PIN code, can read day and total counters, put these to zero and start the descaling programme. TIP ­ For the limited programming menu a operators' PIN code is required, see the fold out sheet at the back of these operating instructions. The programme starts in the carousel (fig. 12 ) of the operators' menu at § 7. 2. 1, "Day counter coffee­making system". ­ When a wrong PIN code has been entered, wait a little while until the initial screen re­appears on the display. ­ Press the selection key (N. ) to go clockwise to the next setting (§ 7. 2. 8), see also fig. 12 . ECopyright Bravilor Bonamat B. V. version 1. 0 19 7. 2. 1 Day counter coffee­making system 7. 2. 2 Day counter hot water system GB G H I J D G H I J D K L M N K L M N Fig. 19 Coffee­making system asks for descaling solution D Remove the plug of the filling hole for descaler solution (B. ). ­ The filling hole of the coffee­making system is found behind the spray head (D. ). D Place the special funnel in the filling hole and carefully pour the descaler solution into the filling hole. ECopyright Bravilor Bonamat B. V. version 1. 0 21 D After pouring in the descaler solution, press the confirmation key (L. ). ­ The resevoir is boiled empty to let the descaler solution run through the flow element. ­ The first level block appears on the display and the hammer symbol flashes (fig. 20 ). ­ When the signal sounds and the level blocks on the display flash, the containers must be emptied. D D D G H I J D D K L M N D Fig. 20 First level descaling programme coffee­making system D Empty the container through the coffee tap. D Press the confirmation key (L. ) to confirm that the container is empty. ­ A sandglass appears on the display for a waiting time of 5 minutes to let the renegite do its job. ­ Also the second level block appears on the display and the hammer symbol flashes. ­ When the signal sounds and the level blocks on the display flash, the containers must be emptied. After this, press the confirmation key (L. ) to confirm that the container is empty. [. . . ] 53 Resetting the day counter of the HW system D Press selection key (M. ) until fig. 53 appears on the display. D Press selection key (N. ) to go to the next setting or press stop key (K. ) to exit the programming menu. 40 version 1. 0 ECopyright Bravilor Bonamat B. V. 8. CORRECTING MALFUNCTIONS WARNING n Check first to determine if the malfunction has a mechanical or electrical origin. Work and repairs on the electrical system may only be carried out by a trained and authorized service technician. GB In case of malfunctions first consult the malfunctions tables. If the problem cannot be solved, consult your Bravilor Bonamat dealer, your service mechanic or one of the service desks. 8. 1 Malfunctioning analysis general LIST OF MALFUNCTIONS Symptom: Possible cause: The switch (P. ) is off. [. . . ]