User manual ALINCO DJ-S 47 E

[. . . ] VHF/UHF FM TRANSCEIVER DJ-S17 E/TFH DJ-S47 E Instruction Manual VOL VOL NAME SQL KL V/M/C SQL KL /C V/MNA ME MW RPT PO MW RPT PO UHF FM TRANSCEIVER UHF FM TRANSCEIVER DJ-S17 DJ-S47 Thank you for purchasing your new Alinco transceiver. This instruction manual contains important safety and operating instructions. Please read this manual carefully before using the product and keep it for future reference. ALINCO, INC. 2 NOTICE / Compliance Information Statement NOTICE / Compliance Information Statement Conformity Information Alinco, Inc. Electronics Division hereby declare on our sole responsibility that the product(s) listed below comply the essential requirements of the Directive 1999/5/EC, The council of 3/9/99 on Radio Equipment and Telecommunication Terminal Equipment and the mutual recognition of their conformity and with the provisions of Annex, after having performed the required measurements at Notified Bodies per Standards, and relative certificate(s) or document(s) can be reviewed at http://www. [. . . ] When a signal is received on the frequency that you selected, and S-meter are displayed on the LCD, then the received signal can be heard. The green RX indicator also lights at this time. 4. 7. 1 Monitor Function In case the receiving signal is weak and the audio is intermittently cut off by the squelch, press the MONI key. As long as this key is pressed, the squelch including TSQ/DCS unmutes making the audio easier to hear. · The squelch is unmuted while the MONI key is pressed, regardless of the squelch level setting. · This function unmutes the squelch even if the DCS and Tone Squelch functions are set. 30 4. Basic Operation 4. 8 Transmitting 1. While holding down the PTT key, speak into the unit at normal voice from the distance of 5cm (2"). IMPORTANT NOTE: · To transmit a tone-burst signal, press the MONI key while holding down the PTT key. · Speaking too loud, too close or too far from the unit may distort the audio. · This unit is equipped with a special kind of cloth over the built-in microphone for water proof. For this reason, a slight change of tone may happen when you use accessories like external microphones, but this is not abnormal. · "OFF" appears on the display and a beep sounds when the PTT key is pressed with the TX frquency set out of the TX range. You can not transmit in this state. 4 4. 8. 1 Selecting the Output Level Press the FUNC key, and while is displayed on the LCD, press the key to switch between high and low transmission power output. When the low power output is selected, " " is displayed on the LCD (nothing is displayed when the high power is selected). The Power-meter display is when transmitting at the low power, and when transmitting at the high power. IMPORTANT NOTE: The output level can't be altered while transmitting. 31 5. Useful Functions 5. Useful Functions 5. 1 Scan Modes The scan function automatically searches the receiving signals. · Timer Scan : The scan stops when a signal is detected, and resumes scanning after 5 (default) seconds regardless of receiving status. · Busy Scan: The scan stops when a signal is detected, stays until the signal is gone then resumes scanning. During scanning, the 1MHz decimal point ( ) on the frequency display flashes. Scanning starts in the direction of the last dial operation (up or down). 5 NOTE: Please refer to the Set mode to switch the setting between Timer and Busy scan modes (page 43). 5. 1. 1 VFO-Scan 1. Rotate the dial clockwise/counter-clockwise to change the scan direction. Press any key other than the MONI key to stop scanning. 5. 1. 2 Memory-Scan 1. [. . . ] Connect the AC adapter plug to the DC-IN jack on the back of the basket. Connect the adapter to an outlet. 10 57 10. Maintenance and Reference 3. Press the sides of the adjustment plate, and attach it to the proper grooves of the basket according to the size of the battery pack. Make sure that the characters A, B and C on both sides of the stand match each other and the plate is placed all the way down to the bottom. Installation Positions of the Adjustment Plate When mounting only the battery (EBP-63/65) When mounting only the battery (EBP-64) A B C A B C A B C A B C EBP-63/65 When mounting the battery attached to the unit (EBP-63/65) When mounting only the battery (EBP-66) When mounting the battery attached to the unit (EBP-66) When mounting the battery attached to the unit (EBP-64) EBP-64 4. [. . . ]