User manual ALCATEL-LUCENT SPEEDTOUCH USB 330

[. . . ] SpeedTouchTM USB/330 ADSL USB Modems Setup and User's Guide Release R3. 0. 1 300 SERIES SpeedTouchTM USB/330 Setup and User's Guide Release R3. 0. 1 Status Change Note Short Title Copyright v4. 0 PeckelbeenS STUSB/330 Setup and User's Guide R3. 0. 1 (en) © 2004 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Contents 1 1. 1 1. 2 SpeedTouchTM Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4 Click the PPP tab to view the PPP configuration: Enter your Account Name and Password in the appropriate fields. Note Select Save password in case you want the computer to remember the password for this account name. Optionally you can enter a name for this connection in the Service Provider field. All other fields may stay empty 5 If your computer runs: · · Mac OS X v10. 1 or v10. 2: You must enter a digit, e. g. Mac OS X v10. 3: You must leave the Telephone Number field empty. 6 Click the Proxies tab to view the proxy settings. As this suits the required SpeedTouchTM configuration, no changes are needed in this panel. E-SIT-CTC-20030702-0003 v4. 0 25 2 SpeedTouchTM Installation 7 Click the Modem tab. This panel shows the modem configuration: Select SpeedTouchTM USB Modem in the Modem list and leave the other modem settings unchanged. 8 Run through all panels again to check whether all configurations are correctly done as described above and click Apply Now to apply the settings. Note To prevent further changes you can click to secure your settings. From then on changes are only possible after providing the Administrator password. As a result your SpeedTouchTM connection is installed and ready for use. The SpeedTouchTM is now prepared for connecting you to the Internet (See "3 SpeedTouchTM Internet Connectivity" on page 27). 26 E-SIT-CTC-20030702-0003 v4. 0 3 SpeedTouchTM Internet Connectivity 3 SpeedTouchTM Internet Connectivity Introduction The SpeedTouchTM supports two connection protocol models: · A PPP (PPPoE or PPPoA) connection See "3. 1 Internet Sessions via a PPP Connection" on page 28 for more information. An RFC1483 Bridged connection See "3. 2 Internet Sessions via an RFC1483 Bridged Connection" on page 36 for more information. · The connection protocol model depends on the selected connection profile during the installation process and should correspond with the ISP's requirements. E-SIT-CTC-20030702-0003 v4. 0 27 3 SpeedTouchTM Internet Connectivity 3. 1 Internet Sessions via a PPP Connection Introduction The SpeedTouchTM supports both most popular connection methods: · · PPP over ATM (PPPoA) PPP over Ethernet (PPPoE) The connection method depends on the selected local setting during the installation process and should correspond with the ISP's requirements. 28 E-SIT-CTC-20030702-0003 v4. 0 3 SpeedTouchTM Internet Connectivity 3. 1. 1 PPP Sessions for MS Windows Starting a PPP session Proceed as follows: 1 Double-click the SpeedTouchTM Dial-up icon on your desktop: Note 2 You can also access the SpeedTouchTM Dial-up application via Start > (All) Programs > SpeedTouchTM USB > SpeedTouchTM Dial-up. As a result the SpeedTouchTM Dial-up window appears: 3 If needed, enter user name and password for your user account at the Service Provider. Note In case of PPPoE connectivity, you may need to enter a Service Name. If so, it will be provided by your Service Provider. 4 5 Click Connect (or Dial). As soon as the connection is established, the connection message box and dial-up window are minimized into a DUN icon in the system tray: You can open your web browser and surf the Internet. E-SIT-CTC-20030702-0003 v4. 0 29 3 SpeedTouchTM Internet Connectivity Network connection icon on the status area While you are connected, you can find the network connection icon showing two PCs connected to each other in the system tray's status area: The network connection icon itself symbolizes activity on the connection: · · A flashing "Front" PC symbolizes upstream (TX) link activity (from your local PC towards the remote device). A flashing "Behind" PC symbolizes downstream (RX) link activity (from the remote device towards your PC). If you move the mouse pointer over the network connection icon, a dialog box appears. Terminating a PPP session Proceed as follows: 1 Double-click the SpeedTouchTM Dial-up icon on your desktop: Or open the SpeedTouchTM Dial-up window via Start > (All) Programs > SpeedTouchTM USB > SpeedTouchTM Dial-up. As a result no Internet connectivity exists anymore. 30 E-SIT-CTC-20030702-0003 v4. 0 3 SpeedTouchTM Internet Connectivity Configuring multiple entries In case you have more than one account, and/or multiple SpeedTouchTM devices connected to your PC, you can create multiple Dial-Up Networking (DUN) entries for the SpeedTouchTM, with specific credentials, properties and home web page. To add additional DUN entries proceed as follows: 1 Double-click the SpeedTouchTM Dial-up icon on your desktop: Or open the SpeedTouchTM Dial-up window via Start > (All) Programs > SpeedTouchTM USB > SpeedTouchTM Dial-up. 2 As a result the SpeedTouchTM Dial-up window appears: 3 4 On the Connection menu, click Add. The Properties window appears: Enter the required information in the corresponding fields and click OK. As a result the new DUN entry is listed in the Connection list in the SpeedTouchTM Dial-up window. E-SIT-CTC-20030702-0003 v4. 0 31 3 SpeedTouchTM Internet Connectivity 3. 1. 2 PPPoA Sessions for Mac OS 8. 6/9. x Note For PPPoE session connectivity, see "3. 2 Internet Sessions via an RFC1483 Bridged Connection" on page 36. [. . . ] The ADSL LED is assigned to the upstream (TX) data channel (towards the ADSL channel). When an ATM cell is processed in a channel, the associated LED will go off for a short time. Troubleshooting table Following table may help you determine the nature of the problem, and provide some plausible solutions: Problem SpeedTouchTMdoes not work. (none of the LEDs light up) Solution Verify the SpeedTouchTM connections. When using a portable computer in battery mode, it is possible that its USB port is not powered. [. . . ]