User manual ALCATEL-LUCENT SPEEDTOUCH BUS 1

[. . . ] SpeedTouchTM 605/608/608WL/620 (Wireless) Business DSL Routers Installation and Setup Guide Release R5. 3. 1 SpeedTouchTM608WL and SpeedTouchTM620 only SpeedTouchTM 605/608 608WL/620 Installation and Setup Guide R5. 3. 1 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] Proceed as follows: Use the grey DSL cable to wire the SpeedTouchTM DSL port to your telephone wall outlet or distributed filter. You can use the orange ISDN cable to wire the SpeedTouchTM ISDN port to your ISDN wall outlet. The SpeedTouchTM608WL/620 is provided with an integrated ISDN modem, that can be activated in case the main link fails. For US/Canada: Do not use the ISDN port; do not attempt to connect this port to the network at anytime. 1 2 ! 3 Plug in the coaxial jack from the electric power supply adapter into the SpeedTouchTM`18VAC' port and the other end to the wall outlet. E-DOC-CTC-20050429-0086 v1. 0 7 Chapter 2 Basic Installation 4 During the SpeedTouchTM Home Install Wizard, you will be asked to make one of following connections: Connect the yellow RJ-45 Ethernet cable to the yellow Ethernet port on your SpeedTouchTM and the other end to the computer's Ethernet port. For wireless networking, plug a wireless card or adapter in your computer. If you will run the SpeedTouchTM Home Install Wizard, as described in "3. 1 SpeedTouchTM Home Install Wizard" on page 12, it is recommended to wait to make these connections until the wizard will ask you to do so. Powering the SpeedTouchTM To power on the SpeedTouchTM, press the powerrocker button on the SpeedTouchTM rear panel. During the start-up procedure, the power LED on the front panel is lit red for some seconds. As soon as the power LED is solidly lit green, your SpeedTouchTM is ready for service. If these LEDs do not light, please refer to "Checking the LEDs" on page 29. A comprehensive LED overview can be found in the SpeedTouchTM User's Guide. To power off your SpeedTouchTM, press the same button. 8 E-DOC-CTC-20050429-0086 v1. 0 Chapter 2 Basic Installation 2. 3 The SpeedTouchTM Setup CD Introduction Your SpeedTouchTM is delivered with a Setup CD. If you insert the CD on a Microsoft Windows PC or Mac OS X computer, an intuitive CD Menu guides you through the features and contents of the Setup CD. To be able to run the applications on the Setup CD on an MS Windows 2000, an MS Windows XP operating system, or Mac OS X computer, you need administrative rights. ! In case of another operating system a set of subdirectories allows you to easily browse for user documentation, SpeedTouchTM system software, service templates, SNMP MIBs, etcetera. Launching the CD on MS Windows or Mac OS X To launch the SpeedTouchTM Setup CD Menu: 1 Insert the Setup CD in your computer's CD-ROM or DVD-ROM drive. If not, refer to "The SpeedTouchTM CD does not start automatically" on page 32. On Mac OS X: If the CD does not autostart, double-click Menu in the window with the content of the CD. 2 3 In the Choose Language window, select the language of your choice and click OK. The SpeedTouchTM Safety Instructions and Regulatory Notices will be displayed in your default web browser. If you accepted the Safety Instructions and Regulatory Notices agreement on this computer before, the instructions are not shown; instead the CD menu pops up. 4 Read all the instructions carefully. If needed you can select another language to read the instructions in the language bar available at the top right corner of the web browser window. Your SpeedTouchTM product is designed and tested to meet the latest safety standards. However, to ensure safe use of this product, it is important that the Safety Instructions and Regulatory Notices shown and/or available in the Safety and Regulatory booklet are read, and complied with carefully, before installing the SpeedTouchTM product. ! 5 If you have carefully read these Safety Instructions and Regulatory Notices, please close the browser window to proceed. You should see the Safety Instructions and Regulatory Notices window inviting you to confirm your reading: 6 Select I have read and I fully understand the Safety Instructions and Regulatory Information and click Continue. As a result the SpeedTouchTM CD menu pops up. E-DOC-CTC-20050429-0086 v1. 0 9 Chapter 2 Basic Installation SpeedTouchTM CD menu The SpeedTouchTM CD menu will pop up automatically each time you insert the CD: Select: Setup my SpeedTouch to start the SpeedTouchTM Home Install Wizard allowing you to prepare your SpeedTouchTM and network for WAN connectivity. See "3. 1 SpeedTouchTM Home Install Wizard" on page 12 for more information. [. . . ] If you did not reconfigure the SpeedTouchTM's IP settings or wireless access point settings, restart the wizard. If the setup fails over a wireless connection, try - if possible - to setup your SpeedTouchTM using a wired connection. If the problem persists, refer to the Service Provider's instructions for more information. SpeedTouchTM documentation cannot be viewed To be able to view the SpeedTouchTM documentation pages on the Setup CD, Javascript must be enabled in your web browser. To allow active content on an MS Windows XP system, see " Active content in Internet Explorer" on page 34. E-DOC-CTC-20050429-0086 v1. 0 33 Chapter 5 Internet Connection Troubleshooting Active content in Internet Explorer When opening documentation pages from the Setup CD a warning might be displayed; this is for instance the case if the pages are opened in Internet Explorer and you are using MS Windows XP with Service Pack 2. [. . . ]