User manual ALCATEL-LUCENT SPEEDTOUCH 716 V5

[. . . ] SpeedTouchTM716v5 (WL) (Wireless) Residential DSL Gateway with Voice User's Guide Release R5. 3. 1 SpeedTouchTM716v5 WL only SpeedTouchTM 716v5 (WL) User's Guide R5. 3. 1 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] A list of telephony services provisioned by your provider is shown: 6 Select those services you want to activate. To deactivate the service, clear the corresponding check box. 7 (De)activating services on your telephone Click Apply. To activate a service using the attached telephone: 1 2 Hook off the phone. You can dial a `#' after the activation code to indicate the end of the code, as a result of which the service will be activated instantly. To deactivate the service, dial a `#' followed by the activation code. 3 Wait for the confirmation tone, and then hook on the phone. The Forced FXO service cannot be activated on your phone. 54 E-DOC-CTC-20050401-0008 v1. 0 Chapter 4 Voice over IP Using the services on the phone In following table the procedures are shown of how to use a telephony service. The commands are depending on your provider's configuration, so might be different from the ones described here. If your phone hasn't got an R or another hook flash button, put down the hook for 1/2 second and then dial the command number. To use the service: Call Hold Proceed as follows: To put person A on hold: 1 2 Dial R, 2 to put the call with person A on hold. Dial R, 1 to retrieve the call on hold. To put person A on hold and set up a call to person B: 1 2 3 Call Waiting Dial R, 2 to put the call with person A on hold. Person B is put on hold. You are in a phone conversation with person A while person B is calling you. The phone produces a waiting tone and - if CLIP is enabled and CLIR disabled - displays the number of person B on the display. To terminate the first call and to switch to the waiting call, dial R, 1. If you do not want to terminate the first call, dial R, 2 to keep the first caller on hold while answering the second call. To return to person A while terminating the call with person B, dial R, 1. Call Transfer You receive a phone call from person A and you want to transfer him to person B. 1 2 3 4 5 6 Dial R, 2. Hang up the phone. E-DOC-CTC-20050401-0008 v1. 0 55 Chapter 4 Voice over IP To use the service: Conference Call (3 Party) Proceed as follows: To set up a conference call: 1 2 3 4 5 6 Call person A. Dial R, 3. Once the conference call has been established, you can: 1 2 CLIR on call basis Dial R, 2 to put the 2 calls on hold. Dial R, 3 to retrieve the 2 held calls. It is possible to hide your phone number for one particular call. To make a phone call over the regular telephone line: Forced FXO 1 2 Dial *01*. Wait for the dial tone, and then dial the phone number of person A. Command overview In the table below all standard service codes of the telephony services are listed. On your SpeedTouchTM these might be different, depending on your provider. Phone command: R0 Is used to: drop a held call reject an incoming call R1 R2 terminate an active call and switch to the waiting or held call put a call on hold switch between active and waiting or held call put a conference call on hold R3 R4 *31* *01* establish a 3-way conference call transfer a call make an anonymous call (use CLIR) on call basis use the regular telephone line 56 E-DOC-CTC-20050401-0008 v1. 0 Chapter 5 SpeedTouchTM Web Interface 5 SpeedTouchTM Web Interface Introduction The SpeedTouchTM comes with embedded HTML pages, providing an interface to the software installed on the device. It allows easy setup and management of the SpeedTouchTM via your web browser form any PC connected to the SpeedTouchTM. See "1. 3. 1 Access via the Web Interface" on page 11 to access the pages. SpeedTouchTM documentation Consult: The SpeedTouchTM Installation and Setup Guide for more information on setup and installation procedures. E-DOC-CTC-20050401-0008 v1. 0 57 Chapter 5 SpeedTouchTM Web Interface 5. 1 Navigation Navigation components The SpeedTouchTM web interface consists of following components: Menu Language Bar Navigation Bar Notification Area Tasks Navigation bar Notification area Language bar Menu Tasks 58 E-DOC-CTC-20050401-0008 v1. 0 Chapter 5 SpeedTouchTM Web Interface 5. 1. 1 Menu Menu items The menu is located on the left side of the page and consists of the following menu items: SpeedTouch: Provides basic information on the SpeedTouchTM. Broadband Connection: Allows you to view/configure your broadband connections. [. . . ] At the end of the procedure the wizard prompts you that the installation was successful. Click Finish to quit. 126 E-DOC-CTC-20050401-0008 v1. 0 Chapter 7 Troubleshooting Adding IGD Discovery and Control Your MS Windows XP system is able to discover and control Internet Gateway Devices (IGD), like the SpeedTouchTM on your local network. Therefore it is recommended to add the IGD Discovery and Control client to your system. Proceed as follows: 1 2 3 4 On the Windows task bar, click Start. [. . . ]