User manual ALCATEL-LUCENT SPEEDTOUCH 620 1

[. . . ] SpeedTouchTM620 Wireless Business DSL Routers CLI Reference Guide Release R5. 3. 1 SpeedTouchTM 620 CLI Reference Guide R5. 3. 1 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] REQUIRED port = <number{1-4}> Note If no port number is specified, then the port number of the Mirror Capture Port is shown. EXAMPLE: =>eth switch mirror capture port=2 =>eth switch mirror capture Mirror capture port = 2 => RELATED COMMANDS: eth switch mirror egress eth switch mirror ingress Enable or disable the specified port to be the Mirror Egress Port. Enable or disable the specified port to be the Mirror Ingress Port. E-DOC-CTC-20050531-0063 v1. 0 303 Eth Commands eth switch mirror egress Enable or disable the specified port to be the Mirror Egress Port. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. SYNTAX: eth switch mirror egress port = <number{1-4}> [state = <{enabled | disabled}>] where: port The port to be the Mirror Egress Port. REQUIRED Note state If no port number is specified, then the port number of the current Mirror Egress Port is shown. The default is enabled. EXAMPLE: Here port 1 is enabled as Mirror Egress Port =>eth switch mirror egress port=1 =>eth switch mirror egress Egress mirror port = 1 => Here port 1 is disabled as Mirror Egress Port =>eth switch mirror egress Egress mirror port = 1 =>eth switch mirror egress port=1 state=disabled =>eth switch mirror egress => RELATED COMMANDS: eth switch mirror capture eth switch mirror ingress Define the specified port to be the Mirror Capture Port. Enable or disable the specified port to be the Mirror Ingress Port. 304 E-DOC-CTC-20050531-0063 v1. 0 Eth Commands eth switch mirror ingress Enable or disable the specified port to be the Mirror Ingress Port. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. SYNTAX: eth switch mirror ingress port = <number{1-4}> [state = <{enabled | disabled}>] where: port The port to be the Mirror Ingress Port. REQUIRED Note state If no port number is specified, then the port number of the current Mirror Ingress Port is shown. The default is enabled. EXAMPLE: Here port 2 is enabled as Mirror Ingress Port =>eth switch mirror ingress port=2 =>eth switch mirror ingress Ingress mirror port = 2 => Here port 2 is disabled as Mirror Ingress Port =>eth switch mirror Ingress mirror port =>eth switch mirror =>eth switch mirror => ingress =2 ingress port=2 state=disabled ingress RELATED COMMANDS: eth switch mirror capture eth switch mirror egress Define the specified port to be the Mirror Capture Port. Enable or disable the specified port to be the Mirror Egress Port. E-DOC-CTC-20050531-0063 v1. 0 305 Eth Commands eth vlan add Add a new VLAN. SYNTAX: eth vlan add name = <string> vid = <number{2-508}> [addrule = <{disabled | enabled}>] where: name vid The new VLAN name. REQUIRED REQUIRED Note addrule The ID 1 is reserved for the default VLAN. OPTIONAL Add (enabled) the default bridge constraint or not (disabled). The default is enabled. EXAMPLE: =>eth vlan list Vid Name -----1 default =>eth vlan add name=myVLAN vid=2 =>eth vlan list Vid Name -----1 default 2 myVLAN => RELATED COMMANDS: eth vlan delete eth vlan list Delete a VLAN. Display all VLANs. 306 E-DOC-CTC-20050531-0063 v1. 0 Eth Commands eth vlan delete Delete a VLAN. SYNTAX: eth vlan delete where: name The name of the VLAN to be deleted. REQUIRED name = <string> EXAMPLE: =>eth vlan list Vid Name -----1 default 2 myVLAN =>eth vlan delete name=myVLAN vid=2 =>eth vlan list Vid Name -----1 default => RELATED COMMANDS: eth vlan add eth vlan list Add a new VLAN. Display all VLANs. E-DOC-CTC-20050531-0063 v1. 0 307 Eth Commands eth vlan flush Flush all VLANs. All the VLANs, except the default VLAN will be flushed. SYNTAX: eth vlan flush EXAMPLE: =>eth vlan list Vid Name -----1 default 2 myVLAN 3 yourVLAN =>eth vlan flush =>eth vlan list Vid Name -----1 default => 308 E-DOC-CTC-20050531-0063 v1. 0 Eth Commands eth vlan list Display all VLANs. SYNTAX: eth vlan list EXAMPLE: =>eth vlan list Vid Name -----1 default 2 myVLAN => RELATED COMMANDS: eth vlan add eth vlan delete Add a new VLAN. Delete a VLAN. E-DOC-CTC-20050531-0063 v1. 0 309 Eth Commands 310 E-DOC-CTC-20050531-0063 v1. 0 Expr Commands Expr Commands Introduction This chapter describes the commands of the expr command group. Contents This chapter covers the following commands: expr add expr delete expr flush expr list expr modify Add a subexpression to an expression. 312 315 316 317 320 E-DOC-CTC-20050531-0063 v1. 0 311 Expr Commands expr add Add a subexpression to an expression. SYNTAX: expr add name = <string> type = <{intf | ip | serv}> addr [!]= <ip-range> [intf [!]= <string>] [intfgroup [!]= <{wan|local|lan|tunnel|dmz|guest} or number>] [tos [!]= <number{0-255}>] [precedence [!]= <IP precedence type> or <number>] [dscp [!]= <DSCP name> or <number>] [proto = <supported IP protocol name> or <number>] [srcport [!]= <supported TCP/UDP port name> or <number>] [srcportend = <supported TCP/UDP port name> or <number>] [dstport [!]= <supported TCP/UDP port name> or <number>] [dstportend = <supported TCP/UDP port name> or <number>] [icmptype [!]= <supported ICMP type name> or <number>] [icmpcode [!]= <number{0-15}>] [icmpcodeend = <number{0-15}>] If a value is preceded by a "!", it means NOT. For example "intfgroup=!wan" means "if the interface group is different from WAN". REQUIRED REQUIRED REQUIRED Note intf Only for expression type ip. OPTIONAL The IP interface name. Note intfgroup Only for expression type intf. [. . . ] OPTIONAL [mode = <{disable | wep | wpa-psk}>] EXAMPLE: =>wireless secmode config No security enabled, open authentication, no data encryption =>wireless secmode config mode=wep =>wireless secmode config Security level WEP: encryption key : 26FF871306 =>wireless secmode config mode=wpa-psk =>wireless secmode config Security level WPA-PSK: preshared key : 26FF871306 encryption : TKIP rekeying : every 0 seconds => E-DOC-CTC-20050531-0063 v1. 0 863 Wireless Commands wireless secmode wep Configure the WEP settings. If the current security mode is WEP, then the security mode must first be changed, before the WEP settings can be (re)configured. SYNTAX: wireless secmode wep where: encryptionkey The secret key to be used for WEP encryption. Two key lengths (64 or 128 bits) and two formats (alphanumeric or hexadecimal) are permitted: for 64-bit encryption: the key must consist of 10 hexadecimal digits or 5 alphanumeric characters for 128-bit encryption: the key must consist of 26 hexadecimal digits or 13 alphanumeric characters. OPTIONAL [encryptionkey = <quoted string>] Note If no encryptionkey is filled in, then the default encryptionkey is used. EXAMPLE: =>wireless secmode wep Security level WEP: encryption key : FFA22E9CCA enabled : yes => 864 E-DOC-CTC-20050531-0063 v1. 0 Wireless Commands wireless secmode wpa-psk Configure the WPA-PSK settings. [. . . ]