User manual ALCATEL-LUCENT SPEEDTOUCH 610 1

[. . . ] SPEEDTOUCH 610 CLI Reference Guide Business DSL Routers 3EC 16982 ACAA TCZZA Edition 01 Status Change Note Released BD F aa 39813 Short Title CD-RG ST610 R4. 1 CLI All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 2 / 384 3EC 16982 ACAA TCZZA Edition 01 Contents Contents About this Document . 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ADSL Commands . 5 27 31 37 47 61 69 75 109 129 137 141 161 179 199 207 261 269 281 287 305 311 317 323 331 337 3EC 16982 ACAA TCZZA Edition 01 3 / 384 Contents 26 27 28 Syslog Commands . [. . . ] SYNTAX: ip ifconfig intf = <interface name> [mtu = <number{293-20000}>] [status = <{down|up}>] [hwaddr = <hardware-address>] [group = <{wan|local|lan}>] The IP interface name. the maximum packet size (including IP header) to use on this interface. The default value depends on the connection and packet service for which the interface was created. OPTIONAL [status] [hwaddr] [group] OPTIONAL OPTIONAL EXAMPLE: =>ip iflist Interface GRP MTU RX 0 loop 1 1500 116 1 eth0 2 3000 21045795 2 NewMer 0 1500 0 5 cip0 0 9180 0 =>ip ifconfig intf=eth0 mtu=1500 =>ip iflist Interface GRP MTU RX 0 loop 1 1500 116 1 eth0 2 1500 21054963 2 NewMer 0 1500 0 5 cip0 0 9180 0 => TX 0 1019664 0 0 TX­DROP 0 0 0 0 STATUS UP UP UP UP HWADDR 00:80:9f:24:ab:cf 00:80:9f:24:ab:cf TX 0 1025417 0 0 TX­DROP 0 0 0 0 STATUS UP UP UP UP HWADDR 00:80:9f:24:ab:cf 00:80:9f:24:ab:cf RELATED COMMANDS: ip config Show/set global IP stack configuration options. 3EC 16982 ACAA TCZZA Edition 01 191 / 384 13 IP Commands ip iflist Show all current interfaces. SYNTAX: ip iflist EXAMPLE OUTPUT: =>ip iflist Interface 0 loop 1 eth0 2 NewMer 5 cip0 => GRP 1 2 0 0 MTU 1500 3000 1500 9180 RX 116 21045795 0 0 TX 0 1019664 0 0 TX­DROP 0 0 0 0 STATUS UP UP UP UP HWADDR 00:80:9f:24:ab:cf 00:80:9f:24:ab:cf RELATED COMMANDS: ip ifconfig Configure interface parameters. 192 / 384 3EC 16982 ACAA TCZZA Edition 01 13 IP Commands ip ping Send ICMP ECHO_REQUEST packets. SYNTAX: ip ping addr = <ip-address> [count = <number{1-1000000}>] [size = <number{1-20000}>] [interval = <number{100-1000000}>] [listen = <{off|on}>] The destination IP address. Listen for incoming ICMP packets (on) or only send ICMP packets (off). REQUIRED OPTIONAL OPTIONAL OPTIONAL addr [count] [size] [interval] [listen] OPTIONAL EXAMPLE: =>ip ping addr=10. 0. 0. 148 listen=off =>ip ping addr=10. 0. 0. 148 listen=on 9 bytes from 10. 0. 0. 148: Echo Request =>ip ping addr=10. 0. 0. 148 count=15 listen=on 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request 9 bytes from 10. 0. 0. 148: Echo Request => RELATED COMMANDS: ip sendto Send UDP packets. 3EC 16982 ACAA TCZZA Edition 01 193 / 384 13 IP Commands ip rtadd Add a route to the SpeedToucht routing table. SYNTAX: ip rtadd dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [src = <ip-address>] [srcmsk = <ip-mask(dotted or cidr)>] [gateway = <ip-address>] [intf = <interface name>] [metric = <number{0-100}>] [type = <number>] The destination IP address(es) for this route. REQUIRED OPTIONAL OPTIONAL OPTIONAL OPTIONAL OPTIONAL dst [dstmsk] [src] [srcmsk] [gateway] [intf] [metric] [type] OPTIONAL OPTIONAL EXAMPLE: =>ip rtlist Destination Source Gateway Intf Mtrc 10. 0. 0. 0/24 10. 0. 0. 0/24 10. 0. 0. 140 eth0 0 10. 0. 0. 140/32 0. 0. 0. 0/0 10. 0. 0. 140 eth0 0 127. 0. 0. 1/32 0. 0. 0. 0/0 127. 0. 0. 1 loop 0 =>ip rtadd dst=10. 10. 0. 0/24 src=10. 0. 0. 0/24 gateway=10. 0. 0. 140 =>ip rtlist Destination Source Gateway Intf Mtrc 10. 0. 0. 0/24 10. 0. 0. 0/24 10. 0. 0. 140 eth0 0 10. 10. 0. 0/24 10. 0. 0. 0/24 10. 0. 0. 140 eth0 0 10. 0. 0. 140/32 0. 0. 0. 0/0 10. 0. 0. 140 eth0 0 127. 0. 0. 1/32 0. 0. 0. 0/0 127. 0. 0. 1 loop 0 => RELATED COMMANDS: ip rtdelete ip rtlist Remove a route from the routing table. Show current routing table. 194 / 384 3EC 16982 ACAA TCZZA Edition 01 13 IP Commands ip rtdelete Delete a route from the SpeedToucht routing table. SYNTAX: ip rtdelete dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [src = <ip-address>] [srcmsk = <ip-mask(dotted or cidr)>] [gateway = <ip-address>] [intf = <interface name>] The destination IP address(es) of the route. REQUIRED OPTIONAL OPTIONAL OPTIONAL OPTIONAL OPTIONAL dst [dstmsk] [src] [srcmsk] [gateway] [intf] EXAMPLE: =>ip rtlist Destination Source Gateway Intf Mtrc 10. 0. 0. 0/24 10. 0. 0. 0/24 10. 0. 0. 140 eth0 0 10. 10. 0. 0/24 10. 0. 0. 0/24 10. 0. 0. 140 eth0 0 10. 0. 0. 140/32 0. 0. 0. 0/0 10. 0. 0. 140 eth0 0 127. 0. 0. 1/32 0. 0. 0. 0/0 127. 0. 0. 1 loop 0 =>ip rtdelete dst=10. 10. 0. 0/24 src=10. 0. 0. 0/24 gateway=10. 0. 0. 140 =>ip rtlist Destination Source Gateway Intf Mtrc 10. 0. 0. 0/24 10. 0. 0. 0/24 10. 0. 0. 140 eth0 0 10. 0. 0. 140/32 0. 0. 0. 0/0 10. 0. 0. 140 eth0 0 127. 0. 0. 1/32 0. 0. 0. 0/0 127. 0. 0. 1 loop 0 => RELATED COMMANDS: ip rtadd ip rtlist Add a route to the routing table. Show current routing table. 3EC 16982 ACAA TCZZA Edition 01 195 / 384 13 IP Commands ip rtlist Show current SpeedToucht routing table. SYNTAX: ip rtlist EXAMPLE OUTPUT: =>ip rtlist Destination 10. 0. 0. 0/24 172. 16. 0. 5/32 0. 0. 0. 140/32 127. 0. 0. 1/32 10. 0. 0. 0/24 172. 16. 0. 0/24 => Source 10. 0. 0. 0/24 0. 0. 0. 0/0 0. 0. 0. 0/0 0. 0. 0. 0/0 0. 0. 0. 0/0 0. 0. 0. 0/0 Gateway 10. 0. 0. 140 172. 16. 0. 5 10. 0. 0. 140 127. 0. 0. 1 10. 0. 0. 140 172. 16. 0. 5 Intf eth0 cip1 eth0 loop eth0 cip1 Mtrc 0 0 0 0 0 1 RELATED COMMANDS: ip rtadd ip rtdelete Add a route to the routing table. Remove a route from the routing table. 196 / 384 3EC 16982 ACAA TCZZA Edition 01 13 IP Commands ip sendto Send UDP packets. SYNTAX: ip sendto addr = <ip-address> [count = <number{1-1000000}>] [size = <number{1-20000}>] [interval = <number{100-1000000}>] [listen = <{off|on}>] [srcport = <number{1-65535}>] dstport = <number{1-65535}> The destination IP address. REQUIRED OPTIONAL OPTIONAL OPTIONAL addr [count] [size] [interval] [listen] [srcport] dstport OPTIONAL OPTIONAL REQUIRED EXAMPLE: =>ip sendto addr=10. 0. 0. 148 listen=on srcport=19 dstport=1025 =>ip sendto addr=10. 0. 0. 148 listen=on srcport=19 dstport=1025 1 bytes from 10. 0. 0. 148:1025 41 A =>ip sendto addr=10. 0. 0. 148 count=3 listen=on srcport=19 dstport=1025 1 bytes from 10. 0. 0. 148:1025 41 A 1 bytes from 10. 0. 0. 148:1025 41 A 1 bytes from 10. 0. 0. 148:1025 41 A => RELATED COMMANDS: ip ping Send ICMP ECHO_REQUEST packets. 3EC 16982 ACAA TCZZA Edition 01 197 / 384 13 IP Commands 198 / 384 3EC 16982 ACAA TCZZA Edition 01 14 IPoA Commands 14 IPoA Commands ipoa ipoa ipoa ipoa ipoa ipoa ipoa ipoa (to access the IPoA level) flush ifadd ifattach ifconfig ifdelete ifdetach iflist 3EC 16982 ACAA TCZZA Edition 01 199 / 384 14 IPoA Commands ipoa flush Flush complete Routed IPoA configuration. SYNTAX: ipoa flush RELATED COMMANDS: ipoa ifadd ipoa ifconfig ipoa ifdelete ipoa ifdetach ipoa iflist Create a new Routed IPoA interface. Show current Routed IPoA interfaces. 200 / 384 3EC 16982 ACAA TCZZA Edition 01 14 IPoA Commands ipoa ifadd Create a new Routed IPoA interface. SYNTAX: ipoa ifadd [intf] [intf = <string>] [dest = <phonebook entry>] The name for the new Routed IPoA interface. In this case the name of the destination will double as interface name. [. . . ] All user and Service Provider specific settings and all saved configuration changes are lost after reboot. SYNTAX: system reset no/yes no/yes = <{no|yes}> Proceed with resetting the SpeedToucht device to its factory default settings (yes) or not (no). By default the system reboot command is discarded in case of no explicit positive confirmation. REQUIRED EXAMPLE: =>system reset ­­­­­­­­­­­­­­­ !! [. . . ]