User manual ALCATEL-LUCENT SPEEDTOUCH 608 WL 1

[. . . ] SpeedTouchTM608 WL Wireless Business DSL Routers CLI Reference Guide Release R5. 3. 1 SpeedTouchTM 608 WL CLI Reference Guide R5. 3. 1 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] REQUIRED intf = <string> RELATED COMMANDS: eth ifattach Attach an ETH interface. 268 E-DOC-CTC-20050531-0061 v1. 0 Eth Commands eth iflist Display the ETH interfaces. SYNTAX: eth iflist where: intf The name of the ETH interface to be displayed. OPTIONAL [intf = <string>] Note If not specified, all the ETH interfaces will be displayed. RELATED COMMANDS: eth ifadd eth ifdelete Create a new ETH interface. Delete an ETH interface. E-DOC-CTC-20050531-0061 v1. 0 269 Eth Commands eth flush Flush all the ETH interfaces. The flush command does not impact previously saved configurations. SYNTAX: eth flush 270 E-DOC-CTC-20050531-0061 v1. 0 Eth Commands eth bridge clear Clear the bridge statistics. SYNTAX: eth bridge clear E-DOC-CTC-20050531-0061 v1. 0 271 Eth Commands eth bridge config Modify/display the bridge configuration settings. SYNTAX: eth bridge config [age = <number{10-100000}>] [filter = <{no_WAN_broadcast | none}>] where: age A number between 10 and 100000 (seconds). Represents the lifetime of a dynamically learned Medium Access Control (MAC) address. The bridge filter to be applied for all Wide Area Network (WAN) bridge ports. Choose between: no_WAN_broadcast: broadcasts from the SpeedTouchTM itself to the WAN are filtered out, broadcasts from the LAN to the WAN are still passed through none: no broadcasts are filtered out. OPTIONAL filter OPTIONAL 272 E-DOC-CTC-20050531-0061 v1. 0 Eth Commands eth bridge flush Flush bridge interfaces and parameters. The flush command does not impact previously saved configurations. SYNTAX: eth bridge flush E-DOC-CTC-20050531-0061 v1. 0 273 Eth Commands eth bridge ifadd Create a new bridge interface. SYNTAX: eth bridge ifadd where: intf The name of the new bridge interface. REQUIRED intf = <string> RELATED COMMANDS: eth bridge ifdelete eth bridge iflist Delete a bridge interface. Display the current bridge interfaces. 274 E-DOC-CTC-20050531-0061 v1. 0 Eth Commands eth bridge ifattach Attach a bridge interface. SYNTAX: eth bridge ifattach where: intf The name of the bridge interface to be attached. REQUIRED intf = <string> RELATED COMMANDS: eth bridge ifdetach Detach a bridge interface. E-DOC-CTC-20050531-0061 v1. 0 275 Eth Commands eth bridge ifconfig Modify a bridge interface configuration. SYNTAX: eth bridge ifconfig intf = <string> [dest = <string>] [portstate = <{disabled | learning | forwarding}>] [retry = <number{0-65535}>] [prioconfig = <{disabled|overwrite|increase}>] [mcastfilter = <{disabled|enabled}>] where: intf dest portstate The name of the bridge interface to be configured. Represents the number of times the SpeedTouchTM retries to set up a WAN connection before giving up. Enable or disable the discard of multicast packets on this port The default is disabled. OPTIONAL REQUIRED OPTIONAL OPTIONAL prioconfig mcastfilter OPTIONAL OPTIONAL 276 E-DOC-CTC-20050531-0061 v1. 0 Eth Commands EXAMPLE: =>eth bridge iflist OBC : dest : Internal . . . BrEthoA_br: dest : (none) Connection State: not-connected Retry: 10 Port: (Unassigned) PortNr: (Unknown) PortState: forwarding =>eth bridge ifconfig intf=BrEthoA_br dest=BrEthhoA_atm =>eth bridge iflist OBC : dest : Internal . . . BrEthoA_br: dest : BrEthhoA_atm Connection State: not-connected Retry: 10 Port: (Unassigned) PortNr: (Unknown) PortState: forwarding => E-DOC-CTC-20050531-0061 v1. 0 277 Eth Commands eth bridge ifdelete Delete a bridge interface. SYNTAX: eth bridge ifdelete where: intf The name of the bridge interface name to be deleted. REQUIRED intf = <string> RELATED COMMANDS: eth bridge ifadd eth bridge iflist Create a new bridge interface. Display the current bridge interfaces. 278 E-DOC-CTC-20050531-0061 v1. 0 Eth Commands eth bridge ifdetach Detach a bridge interface. SYNTAX: eth bridge ifdetach where: intf The name of the bridge interface to be detached. REQUIRED intf = <string> RELATED COMMANDS: eth bridge ifattach Attach a bridge interface. E-DOC-CTC-20050531-0061 v1. 0 279 Eth Commands eth bridge iflist Display the current bridge interfaces. SYNTAX: eth bridge iflist where: intf The name of the bridge interface to be displayed. OPTIONAL [intf = <string>] Note If not specified, all bridge interfaces are shown. RELATED COMMANDS: eth bridge ifadd eth bridge ifdelete Create a new bridge interface. Delete a bridge interface. 280 E-DOC-CTC-20050531-0061 v1. 0 Eth Commands eth bridge macadd Add a static MAC address to a bridge interface. [. . . ] REQUIRED proceed = <{disabled | enabled}> EXAMPLE: =>wireless macacl register proceed=enabled Registration process will be started, new stations can associate during 60 seconds. =>wireless macacl register proceed=disabled => 766 E-DOC-CTC-20050531-0061 v1. 0 Wireless Commands wireless secmode config Configure/show the security mode. SYNTAX: wireless secmode config where: mode The security mode. Choose between: disable: no security wep: Wired Equivalent Privacy (WEP) wpa-psk: Wi-Fi Protected Access (WPA) - Pre-Shared Key (PSK). The default is disable (in other words, by default, there is no security. [. . . ]