User manual ALCATEL-LUCENT SPEDDTOUCH PRO WITH FIREWALL

[. . . ] SPEED TOUCH PRO WITH FIREWALL User's Guide 3EC 36231 ABAA TCZZA Ed. 01 Status Change Note Released BD F aa 36170 Short Title CD-UG STPro 3. 4. 2 All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 2 / 288 3EC 36231 ABAA TCZZA Ed. 11 12 15 16 17 19 20 21 22 23 27 28 29 30 31 32 33 34 35 37 38 39 40 41 43 47 48 49 52 53 54 55 56 59 2 Wiring Guide - Ethernet and ATMF 25. 6 . [. . . ] Note: In case your single Ethernet port STPro is equipped with an ATMF 25. 6 port, VPI values 0 to 7 are cross connected between the DSL port and the ATMF 25. 6 port. 148 / 288 3EC 36231 ABAA TCZZA Ed. 01 13 Networking - ATM Field Type Description Represents the connection service supported on the ATM VC. It can take the following values: Value ETHoA Packet Service Transparent Bridging Routed Ethernet (MER) See chapter 7 for more information. IPoA RFC1483/Rt any CIP & IP Routing See chapter 12 for more information. Any kind of packet service is allowed. RFC1483/Br See chapter 6 for more information. Auto PVC Indicates whether the entry is listed in the 'AutoPVC' list (yes) or not (no). An entry is available if it is not configured in any STPro packet service page, or not in temporary use by a packet service. Phonebook defaults The phonebook entries configured by default are listed in appendix C. 3EC 36231 ABAA TCZZA Ed. 01 149 / 288 13 Networking - ATM The 'ATMF ADSL Xconnects' table The following figure shows the 'ATMF ADSL Xconnects' table: This table, which is only present in case of a dual port STPro, indicates all cross connections between the DSL line and the ATMF25. 6 port. The 'AutoPVC' table The following figure shows an example of the 'AutoPVC' table: Any PVC, identified by its VPI/VCI and communicated via AutoPVC is added to the 'AutoPVC' table. the Digital Subscriber Line Access Multiplexer (DSLAM), the 'AutoPVC' table stays empty. See subsection 13. 3. 3 for more information. 150 / 288 3EC 36231 ABAA TCZZA Ed. 01 13 Networking - ATM 13. 3. 2 Using the Phonebook Introduction The main function of the STPro phonebook is to present an instant overview of all possible entries and their status. Another important function is that it helps you to navigate through the various STPro VC connection possibilities. In this subsection " " " Restrictions for Adding Phonebook Entries Adding Entries Deleting Entries. Restrictions for adding phonebook entries Although you are free to give any name to a phonebook entry, a few restrictions apply: " You may not provide an entry with a name which already is supplied in the 'Phonebook' table. Phonebook entries, which are intended to be used for the Relayed PPPoA packet service may not start with a capital 'P' or a capital 'T'. In case you want to use the STPro PPP to DHCP Spoofing feature the name of the PPP entry you intend to use with this feature must start with 'DHCP', e. g. DHCP_Spoof1, DHCP_2, etc. " " Each entry in the STPro phonebook must have a unique VC, i. e. Adding a phonebook entry with a VPI/VCI, which is already used in the 'Phonebook' table will result in an error message. 3EC 36231 ABAA TCZZA Ed. 01 151 / 288 13 Networking - ATM Adding phonebook entries Proceed as follows: 1. Enter a name of your choice to identify the new phonebook entry in the 'Name' field. Enter the VC's VPI. VCI values in the 'Address' field. Note: In most cases these values are provided by your SP . 5. Select the Connection Service of your choice, or choose any from the 'Type' pop down list. Click and to finish the procedure. Deleting phonebook entries On the 'Phonebook' page, click next to the phonebook entry you want to delete. Click and . Phonebook entries which are currently in use by a packet service ('Available' field = No) cannot be deleted. CAUTION In the case you want to delete a configured phonebook entry, firstly you must delete the entry on the related packet service web page. [. . . ] 01 AppendixD Safety and Agency Regulatory Notices D. 3 Radio Frequency Interference Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. [. . . ]