User manual ALCATEL-LUCENT SPEDDTOUCH 600 3

[. . . ] SpeedTouchTM 600Series Business DSL Routers Orientation Guide Release R4. 2 600 SERIES SpeedTouchTM610 Business DSL Router Orientation Guide Release R4. 2 Status Change Note Short Title Copyright Released PeckelbeenS AppNote ST610 Orientation Guide R4. 2 (en) © 2003 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Contents 1 1. 1 1. 2 1. 3 1. 3. 1 1. 3. 2 1. 4 SpeedTouchTM610 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Configure the SpeedTouchTM610 web page language. Save All The Save All link on the tasks menu allows you to save the SpeedTouchTM610 settings to memory. This can be done via the Upgrade link in the System Config Tasks Links. Help The Help link in the topics menu header allows you to browse the SpeedTouchTM610 online Help. For more information on a specific topic you can click the context-related Help links located at the topic's web pages. E-SIT-CTC-20030306-0004 v2. 0 31 3 The SpeedTouchTM610 Web Interface 3. 2 Quick Tasks Links Easy Setup Click this link to start the SpeedTouchTM Easy Setup wizard. See "1. 3. 2 Configuration Setup for other Operating Systems" on page 17 for more information. System Information Click this link to display the System Information page. The System Information page consists of four sections: · Click the Diagnostics tab to view the results of the System Self Test, LAN Connectivity and DSL synchronization test: · Click the Service Info tab to view the current physical status of the ADSL line: The DSL statistics allow you to view: · · · · Line Status: this shows wether the DSL link is synchronized (Enabled) or not (Initializing). Bandwidth Up/Down: the maximum available bandwidth of the DSL link in both up- and downstream direction. kBytes Tx/Rx: the amount of kilobytes (kBytes) sent (Tx) and received (Rx) since the establishment of the DSL link. 32 E-SIT-CTC-20030306-0004 v2. 0 3 The SpeedTouchTM610 Web Interface · Click the configuration tab to view which configuration profile/file is currently loaded, including information for which Region and ISP this configuration applies: · Click the System tab to view some important system information of the SpeedTouchTM: Connections Click this link to view the Connections page. This page allows you to establish dial-in connections, if applicable: See "2. 1. 2 Internet Sessions via the SpeedTouchTM Web Pages (all OSs)" on page 26 for more information on how to use the Connections table. For more information on the configuration and use of PPP connections, see the application notes "The SpeedTouchTM Routed PPPoA Packet Service" and "The SpeedTouchTM Routed PPPoE Packet Service". E-SIT-CTC-20030306-0004 v2. 0 33 3 The SpeedTouchTM610 Web Interface Diagnostics Click this link to display the Diagnostics page. This page consists of three expandable sections: · Expand the System section to view some important system information: · Expand the Wan section. To view the current DSL state and connection information, expand the DSL and connections sections: Click · to perform an IP connectivity test. Expand the Lan section to view the LAN configuration: 34 E-SIT-CTC-20030306-0004 v2. 0 3 The SpeedTouchTM610 Web Interface Syslog Click this link to display the Syslog page. This page allows you to: · View the syslog messages generated by the SpeedTouchTM610: This page refreshes every 30 seconds. Via the CLI you can configure additional syslog events to be notified by syslog messages in addition to the standard set of syslog events. This allows basic remote monitoring of the SpeedTouchTM610: For more information on Syslog, see the application notes "SpeedTouchTM610 Operation and Maintenance" and "SpeedTouchTM610 Remote Management". E-SIT-CTC-20030306-0004 v2. 0 35 3 The SpeedTouchTM610 Web Interface 3. 3 IP Router Tasks Links IP Addresses Click this link to display the IP Addresses page. This page allows you to view or add/delete specific IP address entries for the SpeedTouchTM610 interfaces: When adding an IP address, all essential IP routes will be automatically be added to the SpeedTouchTM610 IP routing table. The eth0 interface allows you to assign an IP address to the SpeedTouchTM Ethernet interface. This page allows you to view or add/delete static IP routes for SpeedTouchTM610's IP router: Routing can be useful in the case of subnetting your local network. 36 E-SIT-CTC-20030306-0004 v2. 0 3 The SpeedTouchTM610 Web Interface RIP Click this link to display the Routing Information Protocol (RIP) page. This page allows you to: · View or configure the SpeedTouchTM610's general RIP configuration: Via the RIP Settings tab you can enable/disable the master RIP daemon and specify which RIP version should be used. Additionally you can set the default metric and some RIP timer settings. · View or configure the RIP configuration per interface: Per interface you can: · · · · · Override the master RIP status (enable/disable) Override the master RIP version, separately for receiving and sending RIP messages Specify whether authorization is needed or not, and if so the required authorization string Specify whether the scope of RIP on this interface should be narrowed to the applicable IP range. Define one or more RIP neighbors in case multicast messages can not be sent or received among the network Do not forget to save your changes to persistent memory by clicking Save All. E-SIT-CTC-20030306-0004 v2. 0 37 3 The SpeedTouchTM610 Web Interface NAPT Click this link to display the Network Address and Port Translation (NAPT) page. This page allows you to: · View or add/delete specific static NAPT entries: You can add static NAPT entries by 1 2 Click New. [. . . ] no submission is done and a message is sent to the sender that the packet could not be delivered. no submission is done; the packet is silently discarded Count the packet for statistical use (no further action is done on the packet) · · Link the packet to another chain of hooks, i. e. SpeedTouchTM610 Packet Firewall Configuration The SpeedTouchTM610 packet firewall is by default configured to: · · · · · · Drop all traffic migrating from WAN to WAN Drop all traffic from the SpeedTouchTM610 to the WAN, except DNS Allow all traffic from SpeedTouchTM610 to LAN, and vice versa Allow all traffic from LAN to WAN, and vice versa Allow all traffic from a remote LAN to local LAN, and vice versa. You can create other, or additional chains with rules, specific for your needs via the CLI. E-SIT-CTC-20030306-0004 v2. 0 67 4 SpeedTouchTM610 Advanced Concepts 68 E-SIT-CTC-20030306-0004 v2. 0 5 Troubleshooting 5 Troubleshooting Introduction This chapter provides information on how to identify and correct some common problems you may encounter when using and configuring the SpeedTouchTM610. [. . . ]