User manual ALCATEL-LUCENT OMNISWITCH CLI

[. . . ] G March 2005 OmniSwitch CLI Reference Guide www. alcatel. com This user guide documents release 5. 1. 6 of the OmniSwitch 6600 Family, OmniSwitch 7700, OmniSwitch 7800, and OmniSwitch 8800 and release 5. 3. 1 of the OmniSwitch 6800 Series. The functionality described in this guide is subject to change without notice. Copyright © 2005 by Alcatel Internetworking, Inc. This document may not be reproduced in whole or in part without the express written permission of Alcatel Internetworking, Inc. Alcatel® and the Alcatel logo are registered trademarks of Alcatel. [. . . ] (You must also enter a network number and network mask as described above. ) If you are configuring a specific node, enter the node mask. node_mask Defaults parameter vlan allow | block network_number network_mask network_node node_mask default 0 allow 00000000 ffffffff 00:00:00:00:00:00 00:00:00:00:00:00 page 26-16 OmniSwitch CLI Reference Guide March 2005 IPX Commands ipx filter gns Platforms Supported OmniSwitch 6800, 7700, 7800, 8800 Usage Guidelines · Use the no form of the command to delete a GNS filter. · To apply a global filter, use only the basic command syntax (e. g. , ipx filter gns all allow). Do not enter the optional vlan, network, network_mask, network_node, or node_mask parameters. · If you do not enter a network number, the filter will be applied to all networks. · If you do not enter a node number, the filter will be applied to all nodes of the specified network. · The network node number is the physical address assigned to the interface board that connects the device to the network. Examples -> ipx filter gns all block Release History Release 5. 1; command was introduced. Related Commands show ipx filter Displays the current IPX RIP and SAP filters. MIB Objects alaIpxRipSapFilterTable alaIpxRipSapFilterVlanId alaIpxRipSapFilterType alaIpxRipSapFilterNet alaIpxRipSapFilterNetMask alaIpxRipSapFilterNode alaIpxRipSapFilterNodeMask alaIpxRipSapFilterSvcType alaIpxRipSapFilterMode alaIpxRipSapFilterRowStatus OmniSwitch CLI Reference Guide March 2005 page 26-17 ipx type-20-propagation IPX Commands ipx type-20-propagation Enables/disables Type 20 packet forwarding. If Type 20 packet forwarding is enabled on the switch, the switch receives and propagates type 20 packets through all its interfaces. If Type 20 packet forwarding is disabled on the switch, the switch discards, rather than propagates, any Type 20 packet it receives. ipx type-20-propagation [vlan] {enable | disable} no ipx type-20-propagation [vlan] Syntax Definitions vlan enable disable To enable/disable Type 20 packet forwarding on a specific VLAN, enter the VLAN number. Disables Type 20 packet forwarding. Defaults parameter enable | disable default disable Platforms Supported OmniSwitch 6800, 7700, 7800, 8800 Usage Guidelines · Use the no form of the command to disable Type 20 packet forwarding. · To enable/disable Type 20 packet forwarding on all VLANs, use only the basic command syntax (e. g. , ipx type-20-propagation enable). Do not enter the optional vlan parameter. · If Type 20 packet forwarding is enabled it may cause problems with highly redundant IPX networks by causing what appears to be a broadcast storm. Examples -> ipx type-20-propagation enable Release History Release 5. 1; command was introduced. Related Commands show ipx type-20-propagation Displays the current status of Type 20 packet forwarding. page 26-18 OmniSwitch CLI Reference Guide March 2005 IPX Commands ipx type-20-propagation MIB Objects alaIpxType20Table alaIpxType20VlanId alaIpxType20Mode alaIpxType20RowStatus OmniSwitch CLI Reference Guide March 2005 page 26-19 ipx packet-extension IPX Commands ipx packet-extension Enables/disables extended RIP/SAP packets. Larger RIP and SAP packets can be transmitted to reduce network congestion. ipx packet-extension [vlan] {enable | disable} no ipx packet-extension [vlan] Syntax Definitions vlan enable disable To enable/disable extended RIP/SAP packets on a specific VLAN, enter the VLAN number. Disables extended RIP/SAP packets. Defaults parameter enable | disable default disable Platforms Supported OmniSwitch 6800, 7700, 7800, 8800 Usage Guidelines · Use the no form of the command to disable extended RIP/SAP packets. · To enable/disable extended RIP/SAP packets on all VLANs, use only the basic command syntax (e. g. , ipx packet-extension enable). Do not enter the optional vlan parameter. · Transmitting larger RIP and SAP packets reduces network congestion; however, other switches and routers in the network must support a larger, or extended, packet sizes if this feature is configured on the switch. Examples -> ipx packet-extension Release History Release 5. 1; command was introduced. Related Commands show ipx packet-extension Displays the current status of extended RIP and SAP packets. page 26-20 OmniSwitch CLI Reference Guide March 2005 IPX Commands ipx packet-extension MIB Objects alaIpxExtMsgTable alaIpxExtMsgVlanId alaIpxExtMsgMode alaIpxExtMsgRowStatus OmniSwitch CLI Reference Guide March 2005 page 26-21 ipx timers IPX Commands ipx timers Configures the frequency of RIP/SAP updates. RIP and SAP are the routing and service advertising protocols traditionally used by NetWare systems to exchange route and service information on an IPX network. By default, RIP and SAP packets are broadcast every 60 seconds, even if no change has occurred anywhere in a route or service. This command allows you to control how often a router broadcasts these updates. ipx timers [vlan] rip_timer sap_timer no ipx timers [vlan] Syntax Definitions vlan rip_timer sap_timer To configure the IPX timer on a specific VLAN, enter the VLAN number. SAP timer value, in seconds (valid range 1­180). Defaults parameter rip_timer sap_timer default 60 60 Platforms Supported OmniSwitch 6800, 7700, 7800, 8800 Usage Guidelines · Use the no form of the command to return the timers to the default value of 60. · To configure the IPX timer on all VLANs, use only the basic command syntax (e. g. , ipx timers 60 60). Do not enter the optional vlan parameter. · You must set both timer values at the same time (e. g. , ipx timers 120 60). [. . . ] Apptitude, Inc. Provided with this product is certain network monitoring software ("MeterWorks/RMON") licensed from Apptitude, Inc. , whose copyright notice is as follows: Copyright (C) 1997-1999 by Apptitude, Inc. (formerly, Technically Elite, Inc. ), a California corporation with principal offices at 6330 San Ignacio Avenue, San Jose, California, is a third party beneficiary to the Software License Agreement. The provisions of the Software License Agreement as applied to MeterWorks/RMON are made expressly for the benefit of Apptitude, Inc. , and are enforceable by Apptitude, Inc. OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES, INCLUDING COSTS OF PROCUREMENT OF SUBSTITUTE PRODUCTS OR SERVICES, LOST PROFITS, OR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, ARISING IN ANY WAY OUT OF THIS AGREEMENT. I. [. . . ]