User manual ALCATEL-LUCENT OMNISWITCH 6800 GETTING STARTED GUIDE

[. . . ] OmniSwitch 6800 Series Getting Started Guide ® 060195-10, Rev. Only personnel knowledgeable in basic electrical and mechanical procedures should install or maintain this equipment. There is a danger of explosion if the Lithium battery in your chassis is incorrectly replaced. Replace the battery only with the same or equivalent type of battery recommended by the manufacturer. [. . . ] Unlocking All Session Types To unlock all session types, enter the following command syntax at the CLI prompt: -> aaa authentication default local Unlocking Specified Session Types You can also unlock session types on a one-by-one basis. For example, to unlock Telnet sessions only, enter the following command: -> aaa authentication telnet local To unlock WebView (HTTP) sessions only, enter the following command: -> aaa authentication http local You cannot specify more than one session type in a single command line. However, you can still unlock multiple session types by using the aaa authentication command in succession. For example: -> aaa authentication http local -> aaa authentication telnet local -> aaa authentication ftp local 14 Your First Login Session June 2007 Changing the Login Password Change the login password for admin user sessions by following the steps below: 1 Be sure that you have logged into the switch as user All subsequent login sessions--including those through the console port--will require the new password in order to access the switch. The switch allows a maximum of 50 user accounts in the local user database. For information on creating additional user types and assigning individual passwords, refer to the "Managing Switch User Accounts" chapter of your Switch Management Guide. type admin (see "Logging In to the Switch" on page 12). 2 Enter the keyword password and press Enter. 3 Enter your new password at the prompt (refer to the note below). Setting the System Time Zone Note. Typically, the password should be a string of nonrepeating characters. The switch's authentication software uses the first occurrence of the character series to uniquely identify the password. A better password might be engr2735. 4 You will be prompted to re-enter the password. Enter The switch's default time zone is UTC (also referred to as Greenwich Mean Time). If you require a time zone that is specific to your region--or if you need to enable Daylight Savings Time (DST) on the switch--you can configure these settings via the system timezone and system daylight savings time commands. For example, to set the system clock to run on Pacific standard time, enter the following command: -> system timezone pst the password a second time. Be sure to remember or securely record all new passwords; overriding configured passwords on OmniSwitch 6800 Series switches is restricted. New password settings are automatically saved in real time to the local user database; the user is not required to enter an additional command in order to save the password information. Also note that new password information is retained following a reboot. June 2007 To enable Daylight Savings time, enter the following command: -> system daylight savings time enable Your First Login Session 15 Many other time zone variables are supported. For detailed information on configuring a time zone for the switch, refer to your OmniSwitch 6800/6850/9000 Switch Management Guide. Setting Optional System Information This section provides information on configuring optional system parameters, including: · the switch's administrative contact · a system name · the switch's physical location Setting the Date and Time Set the current time for the switch by entering system time, followed by the current time in hh:mm:ss. For example: -> system time 18:35:00 The switch uses a 24-hour clock; the time value shown in the above example would set the time to 6:35 PM. To set the current date for the switch, enter system date, followed by the current date in mm/dd/yyyy. For example: -> system date 06/27/2002 Specifying an Administrative Contact An administrative contact is the person or department in charge of the switch. If a contact is specified, users can easily find the appropriate network administrator if they have questions or comments about the switch. To specify an administrative contact, enter system contact, followed by a text string of up to 254 characters. [. . . ] If its configuration and image files are known to be reliable, you can override the default and initiate a reboot from the /flash/working directory. For more information, refer to your OmniSwitch CLI Reference Guide. Working Directory revised_boot. cfg Hbase. img Hrelease. img Etc. The reload working command overrides the default; the switch runs from Working. Working Directory boot. cfg Hbase. img Hrelease. img Etc. Working and Certified contents are different. Working and Certified contents are different. Working Directory revised_boot. cfg Hbase. img Hrelease. img Etc. Certified Directory boot. cfg Hbase. img Hrelease. img Etc. The switch runs from Certified. Certified Directory boot. cfg Hbase. img Hrelease. img Etc. Certified Directory boot. cfg Hbase. img Hrelease. img Etc. Certified Directory boot. cfg Hbase. img Hrelease. img Etc. When the switch runs from the /flash/certified directory, configuration changes cannot be saved via the write memory command. [. . . ]