User manual ALCATEL-LUCENT OMNIACCESS 4324

[. . . ] OmniAccess 4324 TM Wireless LAN Switch Installation Guide i OmniAccess 4324: Installation Guide Copyright Copyright © 2005 Alcatel Internetworking, Inc. Originated in the USA. Trademarks AOS-W and Alcatel OmniAccess 4324 are trademarks of Alcatel in the United States and certain other countries. Any other trademarks appearing in this manual are owned by their respective companies. ii Part 031640-00 May 2005 Electromagnetic Interference FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] For safety reasons, verify the power outlet and plug are within easy reach of the operator. To minimize electrical hazard, keep water and other fluids away from the product. Comply with electrical grounding standards during all phases of installation and operation of the product. Do not allow the Alcatel Wireless LAN Switch chassis, network ports, power source, or mounting brackets to contact any device, cable, object, or person attached to a different electrical ground. Installation or removal of the chassis must be performed in a static-free environment. The proper use of anti-static body straps and mats is strongly recommended. Do not ship or store this product near strong electromagnetic, electrostatic, magnetic, or radioactive fields. When service or repair is needed, see "Contacting Alcatel" on page ix. 6 Part 031640-00 May 2005 Chapter 2 Requirements Rack Mounting Kit Using the included rack mounting kit, you can mount the Alcatel Wireless LAN Switch in a standard 19-inch network equipment rack. The rack mounting kit contains the following parts: 6-32 Flat Head Screws x6 12-24 Screws Left Bracket Right Bracket x4 FIGURE 2-1 Rack Mounting Kit NOTE--The four 12-24 screws are intended for securing the switch to the rack. Verify that you have the correct screws or fasteners for your rack system before attempting to mount the switch. Installing the Chassis 7 OmniAccess 4324: Installation Guide Selecting a Location The Alcatel Wireless LAN Switch, like other network and computing devices, requires an "electronics friendly" environment. Reliable power Verify that your electrical outlet is compatible with the Alcatel Wireless LAN Switch. The switch power input is auto-ranging and accepts 90~132/180~264 VAC, 50 to 60 Hz, 4. 0/2. 0 A. The power cords must be rated to 10 A and conform to grounded electrical standards in the country where the product is operated. Use of a power line conditioner or Uninterruptible Power Supply (UPS) can decrease or mitigate problems caused by power service fluctuations. Verify that the output of any power shaping device is compatible with the Alcatel Wireless LAN Switch power supply. Cool, non-condensing ventilation For proper operation, the Alcatel Wireless LAN Switch requires an environment with an ambient air temperature between 0 and 40 ºC (32 to 104 ºF). Where a large number of electrical devices are working in the same area, additional air conditioning or air circulation equipment may be required. Ample space For proper air circulation, leave at least 10 cm (4 inches) clearance for the vents on the left and right of the chassis. Leave additional space in front and back of the chassis to access power cords, network cables, and indicator LEDs. Limited electromagnetic interference For best operation, keep the Alcatel Wireless LAN Switch and all cords and cables at least 0. 7 meters (2 feet) from fluorescent lighting fixtures, and 2 meters (6 feet) from photocopiers, radio transmitters, electric generators, and other sources of strong electromagnetic interference. 8 Part 031640-00 May 2005 Chapter 2 Mounting the Chassis 1 Verify that your rack environment meets requirements (see "Selecting a Location" on page 8). Attach the rack mounting brackets to the switch chassis as shown in Figure 2-2. x6 6-32 flat head screws 2 FIGURE 2-2 Attaching the Rack Mounting Brackets Orient both brackets so that the narrow flange faces the front. When placed properly, the brackets' screw holes will match the holes on the side of the chassis. Use a Phillips or cross-head screwdriver to attach each bracket securely with three 6-32 flat head screws (included). Installing the Chassis 9 OmniAccess 4324: Installation Guide 3 Attach the Alcatel Wireless LAN Switch to the rack. CAUTION--To avoid personal injury or damage to equipment, get help for lifting and positioning the Alcatel Wireless LAN Switch. Also, do not install the Alcatel Wireless LAN Switch in any fashion where instability or uneven mechanical loading may occur. NOTE--For proper operation, the Alcatel Wireless LAN Switch requires an ambient air temperature between 0 to 40 ºC (32 to 104 ºF). [. . . ] No AP is detected on the port (lowest precedence). Amber (solid) Green (solid) Off The LED states in Table B-3 are listed in order of precedence (highest to lowest). If more than one AP is connected to the port, the state with the highest precedence is displayed. Pin Outs The RJ-45 female connector pin-outs are shown in Figure B-2 : 10/100 Mbps Ethernet LNK/ ACT POE RJ-45 Female Pin-Out 1 2 3 4 5 6 7 8 Direction Input Output ETH Rx+ (POE negative*) ETH Rx­ (POE negative*) ETH Tx+ (POE positive*) Serial TxD** (POE positive*) Serial TGND** (POE positive*) ETH Tx­ (POE positive*) Serial RxD** (POE negative*) Serial RGND** (POE negative*) *POE optional **Serial optional FIGURE B-2 FE Network Port Pin-outs 20 Part 031640-00 May 2005 Appendix B Cables The type of cable required for each port depends on the device being connected: Direct connection to a SPOE compatible device. This requires an 8-conductor Category 5 UTP Ethernet cable with an RJ-45 male connector. A straight-through cable is required to preserve POE voltage polarity. The port should be connected to the intended device either directly or using a SPOE adapter with no intervening hubs, routers, switches, or other network equipment. [. . . ]