User manual ALCATEL-LUCENT OMNIACCES-VOIP GATEWAY

[. . . ] C April 2004 VoIP User Manual Release 4. 5 An Alcatel service agreement brings your company the assurance of 7x24 no-excuses technical support. You'll also receive regular software updates to maintain and maximize your Alcatel product's features and functionality and on-site hardware replacement through our global network of highly qualified service delivery partners. Additionally, with 24-hour-a-day access to Alcatel's Service and Support web page, you'll be able to view and update any case (open or closed) that you have reported to Alcatel's technical support, open a new case or access helpful release notes, technical bulletins, and manuals. For more information on Alcatel's Service Programs, see our web page at www. ind. alcatel. com, call us at 1-800-995-2696, or email us at support@ind. alcatel. com. This manual documents Release 4. 5 Voice over IP (VoIP) hardware and software. [. . . ] Sets ISDN connection switch type to Euro ISDN (PRI E1 30 B + D channels). o Syntax Notes o If the voice daughtercard connection port type is set to PRI E1, the voice port isdn connection switch type command uses the default value of net5. The port connection type must be set via the voice port interface type command to indicate the number of channels available on the port, e. g. , 2 channels (BRI Euro), 30 channels (E1 PRI ISDN). Default: The default setting is net5 (for VSD), and net3 (for VSB). Command Examples: voice port 2/1 isdn switch type net5 voice port 2/2 isdn switch type net3 Remarks The voice port isdn connection switch type command is used to configure the type of switch connection for the ISDN ports at the voice daughtercard level. Specification of the E1 ISDN protocol is optional unless E1 ISDN PRI or BRI Euro is used. In the "user mode, " set through the voice port isdn protocol command, the ISDN connection switch type uses the switch type to which the ISDN link is connected. In the "network mode, " set through the voice port isdn protocol command, the ISDN connection switch type commands selects the switch type to be emulated. Page 5-53 VoIP Commands voice port bri line type Command Usage Specify ISDN EURO BRI line type (point to point/point to multipoint). (Point to point not available this release. ) Syntax Options voice port <slot/port > isdn bri line type {point to point | point to multipoint} Definitions: slot port point to point Specifies slot number of voice switching daughtercard installed in switching module, (e. g. , 2). Sets physical connection wherein a single network termination point supports a single terminal equipment (TE) device. (Not available this release. ) Sets physical connection wherein a single network termination point supports multipoint terminal equipment (TE) devices. o Syntax Notes o point to multipoint To use this command, the port connection type must be set to bri euro via the voice port interface type command. If the voice daughtercard connection port type is set to bri euro, this command will automatically be generated with the default value of point to point. To use this command, the isdn connection protocol must be set to net via the voice port isdn protocol command. Default: The default setting is point to multipoint Command Examples: voice port 2/1 bri line type point to multipoint voice port 2/2 bri line type point to multipoint Remarks The voice port isdn connection switch type command is used to configure the type of switch connection for the ISDN ports at the voice daughtercard level. Specification of the E1 ISDN protocol is optional unless E1 ISDN PRI or BRI Euro is used. Page 5-54 VoIP Commands voice channel isdn d channel Command Usage Specify control (data or "D") channels for E1 ISDN PRI or BRI Euro. (Not available this release. ) Syntax Options voice channel <slot/port/channel > isdn d channel Definitions: slot port channel Specifies slot number of voice switching daughtercard installed in switching module, (e. g. , 2). Specifies the control (D) channel number (i. e. , 16 for E1 ISDN PRI and 0 for BRI Euro). Syntax Notes o The port connection type must also be set via the voice port interface type command to indicate the number of channels available on the port, e. g. , 3 channels (BRI Euro), 32 channels (E1 PRI ISDN). Only 0 and 16 are allowed for data channel numbers; control channel 16 is reserved for signaling on E1 ISDN PRI, and 0 is reserved for the BRI Euro control channel. For E1 ISDN PRI, channel 0 is used for framing (there is no framing on BRI Euro). Data and corresponding bearer channels must apply to the same voice switching daughtercard. Command Example: voice channel 2/1 16 isdn d channel voice channel 2/2 16 isdn d channel voice channel 2/3 16 isdn d channel voice channel 2/4 16 isdn d channel voice channel 2/1 0 isdn d channel voice channel 2/2 0 isdn d channel voice channel 2/3 0 isdn d channel voice channel 2/4 0 isdn d channel Remarks The voice channel isdn d channel command is used to configure the type of switch connection for the ISDN ports at the voice daughtercard level. Specification of the ISDN protocol is optional if not using E1 ISDN PRI or BRI Euro. Use this table and illustration below to determine valid data/bearer channel, slot and port values (applies to OS/R with two voice switching daughtercards). Interface Data Bearer Slot Port Type Channels Channels Number Number E1 ISDN PRI BRI Euro 16 0 1-30 1-2 2-9 2-9 1-4 1-4 Page 5-55 VoIP Commands Data (D) Channels BRI Euro 0 1 6 2 7 3 8 16 4 5 E1 ISDN PRI 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 27 28 29 31 Bearer (B) Channels (2 B + D channels) BRI Euro (31 B + D channels) E1 ISDN PRI Page 5-56 VoIP Commands voice channel isdn b channel Command Usage Specify E1 ISDN bearer ("B") channels. [. . . ] Specifies port channel number range in which to reset DSP voice play out statistics, (e. g. , 1-12); cumulative for the current call on specified channel. Optional command syntax. Type either stats or statistics in the command line. o Syntax Notes o This command only works from within the command line interface, and cannot be used from within the vsmboot. asc file. Default: None Command Example: voice channel 2/1/1-12 reset voice playout statistics voice channel 2/1/13-24 reset voice playout stats Page 5-276 VoIP Commands voice channel reset dsp stats Command Usage Reset DSP voice play out statistics for one or more voice channels. (Not available this release. ) Syntax Options voice channel <slot/port/startChannel-endChannel > reset dsp stat[istic]s Definitions: slot port channel istic Specifies chassis slot number where VSM is installed, (e. g. , 2). [. . . ]