User manual ALCATEL-LUCENT 716G

[. . . ] SpeedTouchTM716/716g Broadband Voice IAD User's Guide Release R1. 0 SpeedTouchTM716g only SpeedTouchTM 716/716g User's Guide R1. 0 Copyright Copyright ©1999-2005 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. [. . . ] Both SpeedTouchTM716g and your wireless repeater must use: The same WEP key if WEP is enabled. ! WPA encryption is not supported when using WDS. The same fixed channel. The SpeedTouchTM716g and your wireless repeater do not necessarily need to use the same SSID. Using different SSIDs allows you to force your wireless clients to use either the access point of the SpeedTouchTM716g or the access point of your wireless repeater. E-DOC-CTC-20041126-0014 v3. 0 35 Chapter 2 SpeedTouchTM Local Networking Setup SpeedTouchTM716g configuration Proceed as follows: 1 Open the SpeedTouchTM web pages. For more information, see "5. 1 Accessing the SpeedTouchTM Web Pages" on page 44. 2 3 4 5 On the top menu, click Wireless. The SpeedTouchTM716g lists the available networks in following table: 6 Wireless repeater configuration Select your wireless repeater from the list and click Apply. Configure the WDS link with the SpeedTouchTM on your wireless repeater. For more information, consult your wireless repeater's user documentation. As an example, the picture below shows the repeater settings of a SpeedTouchTM180: 36 E-DOC-CTC-20041126-0014 v3. 0 Chapter 3 Configuration 3 Configuration Internet connectivity Some configuration may be required to prepare the SpeedTouchTM for Internet connectivity. What you need from your ISP In most cases, you need a user account with an Internet Service Provider (ISP) for Internet access. For this account, your ISP will provide you with: A user name (logon ID). Other information may be required depending on the ISP's specific requirements and service profile selection. Prerequisites Make sure that: The SpeedTouchTM device is correctly set up and turned on as described in "1. 2 Setting up the SpeedTouchTM" on page 13. See "8. 3 Reset to Defaults" on page 102 for resetting your SpeedTouchTM. The computer's Operating System supports TCP/IP and its Ethernet interface is configured for obtaining its IP configuration dynamically. In case of problems you can also configure the computer's Ethernet or USB interface with a static private IP address, for example 192. 168. 1. 2, 192. 168. 1. 3, but make sure NOT to use 192. 168. 1. 254 as this is the default IP address of the SpeedTouchTM. ! Your web browser is capable and allows to run Javascripts. For more information, see your web browser's help. Configuration procedure Proceed as follows: 1 2 3 4 5 6 7 Start the web browser on your computer. The Quick Setup wizard will guide you through the configuration of your SpeedTouchTM. Follow the instructions and enter the required information where needed. For more information on the different windows shown during this configuration, see " The Quick Setup page" on page 47. 8 At the end of the configuration your SpeedTouchTM will reboot in order to apply the new configuration. E-DOC-CTC-20041126-0014 v3. 0 37 Chapter 3 Configuration 38 E-DOC-CTC-20041126-0014 v3. 0 Chapter 4 SpeedTouchTM Internet Connectivity 4 SpeedTouchTM Internet Connectivity Introduction This chapter provides information on how to configure your SpeedTouchTM according to your preferences and how to access the Internet. Access methods As soon as the SpeedTouchTM and your computers have been configured as outlined in "3 Configuration" on page 37, you are able to connect to the WAN or Internet. Depending on the configuration of the SpeedTouchTM you may have: Direct access As soon as the initial configuration has been done, continuous and immediate access is available via the DSL line. The applied connection protocol model depends on the service profile you selected to configure the SpeedTouchTM and should correspond with the Service Provider's requirements. Direct access As mentioned, as soon as the initial configuration has been done, immediate and uninterrupted WAN access is provided. In case of direct access, the remote organization might ask for a user name and password on an Internet welcome page. Dial-in access The SpeedTouchTM supports both most popular connection methods: PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE). The connection method depends on the service profile you selected to configure the SpeedTouchTM and should correspond with the service Provider's requirements. Routed PPPoA: the SpeedTouchTM needs to be configured for the Routed PPPoA Service. Routed PPPoE: the SpeedTouchTM needs to be configured for the Routed PPPoE Service. [. . . ] Proceed as follows: 1 2 3 4 On the Start menu, click Control Panel. The Windows Components Wizard appears: Select Networking Services in the Components list and click Details. 5 The Networking Services window appears: Select Internet Gateway Device Discovery and Control Client and click OK. 6 7 Click Next to start the installation and follow the instructions in the Windows Components Wizard. At the end of the procedure the wizard prompts you that the installation was successful. Click Finish to quit. E-DOC-CTC-20041126-0014 v3. 0 101 Chapter 8 Support 8. 3 Reset to Defaults Using the SpeedTouchTM web pages Proceed as follows: 1 Open the SpeedTouchTM web pages. [. . . ]