User manual ALCATEL-LUCENT 360

[. . . ] SpeedTouchTM 350/360 ADSL Modems Setup and User's Guide R4. 2. 7 300 SERIES SpeedTouchTM 350/360 R4. 2. 7 Status Short Title Copyright v2. 0 Setup and User's Guide ST350/360 R4. 2. 7 (en) © 2004 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Contents 1 1. 1 1. 2 1. 3 1. 3. 1 1. 3. 2 SpeedTouchTM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] As soon as another DHCP server is found, the SpeedTouchTM will behave as DHCP client, i. e. a DHCP client will be created on its Ethernet interface and the SpeedTouchTM DHCP server will not be started. If no concurrent DHCP server is found, the SpeedTouchTM DHCP server is started. If the SpeedTouchTM DHCP server was running, it will be stopped immediately. Existing SpeedTouchTM DHCP client entries are deleted Always click Apply after changing the DHCP server configuration. · · Note · In case the SpeedTouchTM DHCP server is running, the Server Leases tab allows you to view the currently provided leases. If needed, you can also manually add static DHCP leases for specific hosts. To make dynamically assigned leases static, select the entry and click Lock. The Address Pools tab allows you to view the SpeedTouchTM DHCP server lease pool properties. One DHCP pool (LAN_Private) is defined by default which will be activated if you enable the SpeedTouchTM DHCP server. · · Click the DHCP Client tab to view the current SpeedTouchTM DHCP client entries, if present: By default (as shown above) the SpeedTouchTM DHCP client will be disabled, i. e. no DHCP client entries are present. E-DOC-CTC-20031204-0011 v2. 0 29 3 SpeedTouchTM Web Interface DNS Click this link to display the Dynamic Name System (DNS) page. This page allows you to: · View the current SpeedTouchTM DNS server hostname leases: Via this table you can also add static DNS hostname entries. By adding a name for your network printer, identified by its IP address, you will be able to contact this printer by name rather than by IP address. · View and/or supply the SpeedTouchTM DNS domain name and to enable/disable the SpeedTouchTM DNS server: Note System The use of DNS subdomains is supported, e. g. dsl. office. lan. Click this link to display the Configuration page. · Back up the current SpeedTouchTM configuration, restore the SpeedTouchTM default configuration, or upload a backup configuration file: · · To backup the current configuration click Backup and follow the instructions. To restore the SpeedTouchTM defaults, click Restore default and follow the instructions to confirm the reset. 30 E-DOC-CTC-20031204-0011 v2. 0 3 SpeedTouchTM Web Interface · To upload and apply a SpeedTouchTM backup configuration file: 1 2 3 Click Browse to locate the backup file on your local disk you intend to restore. Click Upload to upload and temporarily apply the backup configuration. Once uploaded, the SpeedTouchTM asks you to confirm that you want the SpeedTouchTM to effectively apply the uploaded configuration. Note Once confirmed, the previous configuration is irrevocably lost. · View the current system software version, identification and the SpeedTouchTM board type: · Check for the latest SpeedTouchTM software upgrades. See "4. 2 SpeedTouchTM System Software Upgrade" on page 44 for upgrade instructions. Note Language Click this link to view the Language page. This page allows you to select the SpeedTouchTM web page language. By default, the only available language is English. Another language can be made available on the SpeedTouchTM web pages by running the SpeedTouchTM Setup wizard using the CD Browser. When the setup procedure is finished, this language will have been enabled on your SpeedTouchTM and the language will be available on the SpeedTouchTM web pages (next to English). E-DOC-CTC-20031204-0011 v2. 0 31 3 SpeedTouchTM Web Interface 32 E-DOC-CTC-20031204-0011 v2. 0 4 Support 4 Support In this chapter This chapter contains the following topics: Topic SpeedTouchTM Configuration Setup SpeedTouchTM System Software Upgrade Resetting the SpeedTouchTM Troubleshooting Page 34 44 52 53 E-DOC-CTC-20031204-0011 v2. 0 33 4 Support 4. 1 SpeedTouchTM Configuration Setup Internet connectivity In most cases no additional configuration of your SpeedTouchTM is required. You can immediately connect your computer to the Internet as described in "2 SpeedTouchTM Internet Connectivity" on page 15). [. . . ] To retrieve this address see " System Information" on page 25. Make sure a valid SpeedTouchTM system software image file is available on your local disk. 50 E-DOC-CTC-20031204-0011 v2. 0 4 Support Procedure To upgrade/restore the SpeedTouchTM system software: 1 In a preliminary step, make sure that your SpeedTouchTM is powered off and that a BOOTP server is readily installed on the computer from which you intend to perform the system software upgrade. Configure the BOOTP server to use the SpeedTouchTM system software image file in its reply to BOOTP requests from the SpeedTouchTM you want to upgrade. To identify the BOOTP requests from the SpeedTouchTM, you will need to specify its MAC address and define an IP range for basic communication between the BOOTP server and the SpeedTouchTM. [. . . ]