User manual ALCATEL-LUCENT 2315

[. . . ] 9. 10. 2315 OPERATION MANUAL 2315 Hotel set The manufacturer reserves the right to modify any product characteristics without prior notice. - http://www. tech-man. com 1. LAYOUT Message indicator signal select switch (under index label) Service buttons Data port Jack RING VOL Ringer volume 123 456 789 * - Mail button & indicator 0# + Speakerphone indicator (handsfree) Speakerphone led (handsfree) Receive volume control 2. INSTALLATION 3 2315 Hotel set The manufacturer reserves the right to modify any product characteristics without prior notice. RCS Nanterre 390 546 059 Before connection to the PBX, the service buttons, ringer melody and flash timing should be pre-programmed according to the customization parameters, either with the customization tool or by manual entry. [. . . ] RCS Nanterre 390 546 059 3. 2. · Handsfree mode: Press the Speakerphone indicator button. Listen for dial tone Dial the number by pressing the dial keypad or any of the service buttons or the Mail button. Press the + or ­ button to adjust receive volume To converse in handset mode, just pick up the handset. Press the Speakerphone indicator button when conversation is finished. The Speakerphone led will be off. 4. INCOMING CALL The ringer volume can be adjusted with the slide switch at the side of the cabinet. Ringer pitch is defined during customization. 4. 1. Handset mode: Pick up handset, and talk to the caller. To switch to handsfree mode, press the the Speakerphone indicator button and return the handset to cradle. Hang up to finish call. 4. 2. Handsfree mode: Press the Speakerphone indicator button ton and talk to the caller. Press the Speakerphone indicator button again to finish call. 5. HOLD A call can be placed on hold any time during conversation. During hold, the phone will send beeps every 10s to the loudspeaker and other party. 5. 1. Handset mode Press HOLD button. To retrieve the call, just press the HOLD key again 5. 2. Handsfree mode 5 2315 Hotel set The manufacturer reserves the right to modify any product characteristics without prior notice. To retrieve the call, just press the HOLD key again 6. HOLD TRANSFER A call can be placed on hold and pick up at a parallel phone. If the call is not picked up, the phone will release the line after 60s. 6. 1. Handset mode Press HOLD button. The Speakerphone led turns off as the 2315 releases the line. 6. 2. Handsfree mode Press HOLD button. The Speakerphone led Flashes Press the Speakerphone indicator button again, The Speakerphone led flashes rapidly. 7. 1. SPECIAL SIGNALLING KEYS : RD last number redial Pressing the RD button right after on line will redial the last number. [. . . ] Inside manual programming mode, the following operations are supported : · · · · re-program & erase the 12 direct memory keys re-program & erase mail access key Select the Flash timing Select the ringer pitch. In manual programming mode, other normal operations are inhibited. 9. 1. Select manual programming Mode Take the handset off hook while pressing R (flash). Continue pressing R (flash) for 2 seconds Two beeps signals the phone is now in manual programming mode. 9. 2. Setting Service buttons or Message Key Code Press HOLD Press the destination service button or MESSAGE button Dial the number (To insert a Flash press R) Press HOLD again A long beep is generated to confirm memory setting 9. 3. Erasing Service buttons or Message Key Code Press HOLD Press the destination service button or MESSAGE button Press HOLD again without entering anything A long beep is generated to confirm memory is erased 7 2315 Hotel set The manufacturer reserves the right to modify any product characteristics without prior notice. RCS Nanterre 390 546 059 9. 4. Setting Flash Timing Press HOLD Press FLASH Press: · · · 1 for 100 ms · 3 for 300 ms · 6 for 600 ms Press HOLD again A long beep is generated to confirm Flash Timing is programmed. 9. 5. Setting Melody Press HOLD Press RD Press: · 1 to select pitch 1, pitch 1 has a higher frequency · 2 to select pitch 2, pitch 2 has a lower frequency Press HOLD again A long beep is generated . 9. 6. Exiting manual programming mode To exit manual programming mode, just hang up. [. . . ]