User manual AKAI TX3310

[. . . ] A serious electric shock could result if you ignore the precautionary measure. If a problem occurs during operation (the sound is interrupted, indicators fail to light up, smoke is detected, etc. ) contact your dealer or Authorized Service Center immediately. Disconnect the power supply if the unit will not be used for a long time. Otherwise the operation life could be shortened. E-2 CAUTION! THIS PRODUCT UTILIZES A LASER. [. . . ] " disappears from the display. NOTES: · · If the CD trays are empty, the TUNER source will be selected instead. The time function will be activated again after 24 hours. SLEEP SETTING: This timer turns power to your system off at the set time. · When enjoying the desired source, press SLEEP to select the desired time. · Each time you press the button, it changes the number of minutes shown on the display in this sequence: · To cancel the sleep timer, press the SLEEP button once and "SLEEP" will go out in the display. E-4 LOCATION OF CONTROLS 1. Cassette door (B) Record button Play button Rewind button F. Fwd button Stop/Eject button Pause button 2 TAPE A 10. Play button Rewind button F. Fwd button Stop / Eject button Pause button Cassette door (A) Display Remote sensor Standby indicator Power button Timer button Sleep button CD button Tuner (Band) button Preset EQ button Tape button Memory / Prog / Clock Adj button Volume control Repeat / Pre-up button Random / Pre-down button Tuner / CD skip (up / down) search button CD stop button CD play / pause button Mode button Disc skip button CD door open / close button FM antenna Beat cut / FM mode / Dubbing speed selector Speaker Terminal AC cord Reset button 3 15 4 5 6 7 8 9 10 11 12 14 13 17 18 16 19 20 21 22 23 24 25 26 27 28 35 34 33 32 31 30 29 36 40 37 38 39 E-5 LISTENING TO THE RADIO Manual tuning 1. a) For FM Stereo reception: The unit provides FM MONO / STEREO selector. In STEREO mode, the unit will automatically switch to stereo when an FM stereo broadcast is received and stereo mark turn on in the display. b) For FM MONAURAL (MONO) reception: To receive weak (noisy) FM station, to set FM MONO / STEREO selector to MONO position. (For more than 2 seconds, then release this button) TUNING button again. To stop the auto tuning, press the Preset stations This unit equipped 40 stations for FM and AM (MW). Once they are preset, broadcasting corresponded to those can readily be enjoyed by simply pressing the preset station button. · Repeat the above procedure to store other preset stations. TUNING TO PRESET STATIONS · ­ Press PRESET DN or UP (or on the remote control) to select the desired preset number. The preset number, frequency and waveband appear on the display. LOADING AND PLAYING CDs 1. · CDs can be placed on any open position on the disc tray. CAUTION: Do not stack CDs in the tray. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. · The music schedule will be displayed only for the number of tracks on the disc. · Playback will begin from track 1 on the disc you have specified to play. Note: If the OPEN / CLOSE button is pressed whilst a CD is being played, the current CD will continue its playback, the disc tray will open and you can replace any CD other than the one which is being played. E-6 TO INTERRUPT PLAYBACK: 1. button to resume playback from the same point. TO STOP PLAYBACK: Press the STOP button. TO REMOVE THE CDs: Whilst in the stop mode, press the OPEN / CLOSE button. Then press the DISC SKIP button to rotate the disc tray and remove the remaining disc. Selecting a desired track Selecting a desired track at the stop mode 1. button once it will skip to the beginning of the current track and play the track Searching for a particular passage during play · Press and hold or button until the desired passage is located. During the search the sound is played faster than normal at reduced Volume play returns to normal when or button is released. [. . . ] Press PLAY key of Tape A / 1 and Record Key together with the PLAY Key of Tape B / 2 at the some time then both Tapes start dubbing synchronously. Adjust the VOLUME Controls to the desired output level and also for the monitoring purpose. To STOP DUBBING, press both STOP / EJECT Keys. High speed dubbing ­ Following the steps of normal speed dubbing procedure, but set the dubbing mode selector to "HIGH SPEED DUBBING" position. E-9 REMOTE CONTROL TRANSMITTER BATTERY INSTALLATION The infrared transmitter requires 3. 0 volts for operation. BUTTON DESCRIPTION 1. DISC SKIP TIMER RANDOM/PRESET For CD For TUNER PLAY/PAUSE TUNING/SKIP For CD For TUNER Stop PRESET EQ VOLUME+/CD POWER button TAPE TUNER/BAND MUTE / ­ To select previous / next CD track. [. . . ]