User manual AKAI GX-F620 SERVICE MANUAL

[. . . ] Insert rechargeable batteries in accordance with polarity symbols (the instructions are found in the handset battery compartment). cable ducts ! i Use the batteries indicated in these operating instructions (see page 17). Do not operate the telephone in environments where there is risk of explosion (e. g. Do not install the base station in bathrooms or showers. The handset is not splashproof (see page 17). Do not pass your Dialon GX-F620 on to a third party without the user guide. [. . . ] When the mute function is enabled the display shows åååå. Disable MUTE function: Enable MUTE function: i Press to continue the call. 8 Call timer Your handset automatically times the duration of all external calls, showing it on the display. It starts showing 20 seconds after the handset goes into the active state and ends 5 seconds after the call is finished. The maximum duration time displayed is 99 minutes and 99 seconds. Inserting a pause You can use this function to insert a pause before you press c and before the telephone number is transmitted. The pause time is fixed to two seconds. Battery performance N After charging your handset batteries during 15 hours for the first time, subsequent charging time is approximately 4­5 hours when the batteries are almost flat. N You can place the handset in the base station after a call to optimize the battery performance. The display shows a P for each pause inserted. Operating two or more handsets at one base station You can register up to four handsets at one base station. This allows you to make costfree internal calls between handsets or enquiry calls and conference calls. The external user is put on hold. ~ R Press longer than one second. The external user is put on hold. ~ Enter the internal call number. When the user answers, you can announce the call. Note: You can forward the call without waiting. The display shows the available handset numbers when linked to the base station. Note: If four handsets are registered at the base station, no further handset can be registered. You will hear the ERROR beep and the handset returns to the idle display. ~ Register Dialon GX-F620 handset at a base station N One Dialon GX-F620 handset can be registered to only one base station. up to four handsets. N One Dialon GX-F620 base station can register Enter one of the handset numbers. If the registration was successful, the idle display shows the new handset number. 13 Modify handset PIN To protect your handset settings from unintentional access you should change your handset PIN (personal identification number). Note: The factory setting of the PIN is 0000. If you do not change this setting, you enter directly the HANDSET SETUP menu. BASE SETUP menu Set base station ringer volume You can choose from four ringer volumes: 2 Press. 1 below). ~ i Press. If necessary, enter base station PIN. i Press. c Press to confirm. q Select the ringer volume (see table c Press to confirm. Display shows P :ç 11 0 P :ç 11 1 P :ç 11 2 P :ç 11 3 Volume setting Ringer OFF LOW MEDIUM HIGH Delete phone book / redial memory You can delete the entire handset memory. i Press. L Press. ~ If necessary, enter handset PIN. Set base station ringer melody You can choose from three melodies: c Press to delete. Restore factory settings To restore the factory settings for the handset: 2 Press. q Select the ringer melody (see table below). ~ i Press. If necessary, enter base station PIN. i Press ~ 2 Press. 1 Press. If necessary, enter handset PIN. Q Press. c Press to confirm. Display shows P :ç 12 1 P :ç 12 2 P :ç 12 3 Melody MELODY 1 MELODY 2 MELODY 3 c Press to restore the factory settings. Note: The reset will set all data to the factory defaults. The PIN is reset to 0000. 14 Set Date and time Date and time are shown in the idle display (see page 2). Change flash time You need only adjust this setting if your PABX requires a different flash time to the pre-set flash time of 100 milliseconds. [. . . ] Never use a dry cloth as this can cause static discharge. Problem Registration did not work. Cause The battery is not sufficiently charged. The batteries are not charged. Remedy Contact with liquid ! No display. If the handset should come into contact with liquid, on no account switch the device on. Allow the liquid to drip out of the device, and then dab all parts of the device dry. Keep the handset with the batteries removed in a warm, dry place for at least 72 hours. [. . . ]