User manual AIWA HV-FX7800

[. . . ] · The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. · Keep the unit and discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers. · Do not place the unit on surfaces (rugs, blankets, etc. ) or near materials (curtains, draperies) that may block the ventilation slots. Caution For use of the VCR Television programs, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. [. . . ] After 5 minutes the unit will stop the tape to prevent damaging the tape or the unit. · Still picture quality can be improved slightly by pressing CH/TRACKING i+/k­. AUDIO C. LOCK SP/LP CM SKIP SHOWVIEW 4 Slow motion: During still picture hold down t (SLOWT). The picture will be slowed down at about 1/19 times the normal playback. · During slow motion, the noise bars may appear on the picture according to the status of tape. If distortions can be seen in the picture, reduce them with CH/TRACKING i+/k­. · If slow motion continues for more than 3 minutes, the unit will automatically change to normal playback. Playing a Tape You will only be able to load and eject video cassettes when the unit is plugged into an AC outlet. Getting a better picture When a cassette is inserted and playback started, the automatic tracking function works to get the best possible picture automatically. If the quality of the recording is poor, repeatedly press CH/TRACKING i+/k­ on the remote control or CHANNEL +/­ on the front panel to manually adjust the tracking until any distortions have been removed. Note Automtic tracking returns to the normal position when the video cassette is ejected. 5 Press C to continue playing your tape. Press z. · If the end of the tape is reached, the unit will stop playback automatically, rewind, stop, eject the tape. 6 Fast Forward/Rewind Search From the STOP mode you can press t or r to quickly move through the tape. If you wish to see a portion of the tape during t or r press and hold t or r. While the buttons are held down the picture is played back at 7 times normal speed. ShowView Codes are published in most TV guide magazines; they can vary one to nine numbers in length. Press OK/ENTER. If PLEASE CHECK is displayed it means that you have entered the wrong ShowView number, entered the ShowView number incorrectly. If "- -" is displayed, you have to enter the program number of the station, you want to record from. PR ARD ------DATE 12 ------TIME 10 : 11 ~ 11 : 55 - - : - - ~ - -: - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - SP SP SP SP SP SP SP E 1 2 Press VIDEO to switch out to the VCR. Make sure that TV channels have been tuned and stored in correct ShowView order. Press SHOWVIEW. 7 3 Press j/l to select the settings that you wish to revise (PR: preset the channel position or TV station's name, DATE, TIME, VPS/PDC and tape speed: SP, LP or IP). Press i+/k­ to enter the correct information. PR ARD ------DATE 12 ------TIME 10 : 11 ~ 11 : 55 - - : - - ~ - -: - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - SP SP SP SP SP SP SP E --------ONCE REC SHOWVIEW 0~9, OK E 34 Operation with Tape (Continued) 8 · IP mode determines how much tape is left and switches speed from SP to LP, if necessary, to complete recording the program. · If you wish to record from the EURO AV1/2 or AV 3 IN jacks, press INPUT SELECT to select for correct display (AV1, AV2 or AV3). PR DATE ARD 12 ------------VPS/PDC : TIME 10 : 11 ~ 11 : 55 - - : - - ~ - -: - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - - - : - -~- - : - ON SP SP SP SP SP SP SP i 9 Check that the timer event details are correct. will appear in the display while the unit waits to make the recording. · If PLEASE CHECK is displayed, you have entered incorrect information and will need to re-enter the data. · If the program overlaps another, see page 37. Notes · Do not set PDC/VPS to ON for a non-PDC/VPS channel. · When the PDC/VPS signal drops out because the broadcast signal is weak, or when a broadcasting station does not transmit a regular PDC/VPS signal, the timer recording will be performed in the normal mode (without PDC/VPS) even if it was programmed for PDC/VPS. 10 Press i/SETUP twice and press I/6 to turn off Note If the timer program list and "PROGRAM FULL" appear on the TV screen in step 2, 7 programs are already set. Cancel an unnecessary program. 35 OPERATION Press j/l until the blank space between endtime and tape speed is highlighted. [. . . ] Select JPEG icon using i+/k­, then press OK/ ENTER. · If JPEG folders are displayed, press i+/k­ to select a JPEG folder, then press OK/ENTER. 4 Press j and i+/k­ to select a file to start playback. · To move to the next page, press TOP MENU. · To move to the previous page, press DISC MENU. 3 Press i+/k­ to select a JPEG file. · To move to the next page, press TOP MENU. · To move to the previous page, press DISC MENU. JPEG jpg 5 Press C or OK/ENTER. · Playback starts from the selected file in order. · Playback stops after the last file within the folder has been played. DSCF 0001 DSCF 0002 DSCF 0003 DSCF 0004 DSCF 0005 DSCF 0006 DSCF 0007 1 / 300 1024X683 Slide Speed Off To return to the menu during playback Press sSTOP or vRETURN. A preview of each file selected from the list of the left is displayed on the right and directory information is displayed at the bottom of the screen. 51 OPERATION Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptom No power. [. . . ]