User manual AIRLIVE WMM-3000PCM

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. -1AirLive MIMO-G Wireless LAN Adapter User's Manual FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. [. . . ] ASCII128bits13 ASCII characters. 4-2-1 802. 1x Setting 802. 1x is a authentication for WPAand WPA2certificate to server. Server certificates identify a server, usually an authentication or RADIUS server to clients. Most EAPs require a certificate issued by a root authority or a trusted commercial CA. Allow intimidate certificates: It must be in the server certificate chain between the server certificate and the server specified in the certificate issuer must be field. Server name: Enter an authentication sever root. - 18 - AirLive MIMO-G Wireless LAN Adapter User's Manual - 19 - AirLive MIMO-G Wireless LAN Adapter User's Manual 4-3 Profile Page Profile can book keeping your favorite wireless setting among your home, office, and other public hotspot. You may save multiple profiles, and activate the correct one at your preference. 1. Network Type: Network's type, icluding infrastructure and Ad-Hoc. Connection status Indicate connection is successful on currently activated profile. Edit Profile Activate selected profile. - 20 - AirLive MIMO-G Wireless LAN Adapter User's Manual 4-4 Link Status Page Show the information of linking status. As show in picture 20, the description of each session is said as following: 1. Throughout: Display transmits and receive throughput in unit of K bits/sec. Link Quality: Display connection quality based on signal strength and TX/RX packet error rate. Signal Strength: Receive signal strength, user can choose to display as percentage or dBm format 7. Noise Level: Display noise signal strength. - 21 - AirLive MIMO-G Wireless LAN Adapter User's Manual 4-5 Statistics Page Statistics page displays the detail counter information based on 802. 11 MIB counters. This page translates that MIB counters into a format easier for user to understand. 1. Frames Transmitted Successfully Without Retry: Frames successfully sent without any retry. Frames Transmitted Successfully After Retry: Frames successfully sent with one or more reties. Frames Fail To Receive ACK After All Retries: Frames failed transmit after hitting retry limit. RTS Frames Successfully Receive CTS: Successfully receive CTS after sending RTS frame. RTS Frames Fail To Receive CTS: Failed to receive CTS after sending RTS. Frames Dropped Due To Out-of-Resource: Frames dropped due to resource issue. Duplicate Frames Received: Duplicate received frames. 3. To zero the statistic numbers of transmitting and receiving data. - 22 AirLive MIMO-G Wireless LAN Adapter User's Manual Advance Page The advance setting is shown as follows. [. . . ] Those setting are same as our intended AP's setting. - 52 - AirLive MIMO-G Wireless LAN Adapter User's Manual ii. Click OK. The result will look like the below figure. 2. TLS / Smart Card: - 53 AirLive MIMO-G Wireless LAN Adapter User's Manual i. Authentication type chooses TLS / Smart Card, TLS only need identity that is wpatest2 for server authentication. ii. TLS must use client certicate. Click more to choose certicate. iii. Certicate page will pop up; choose a certicate for server authentication. - 54 AirLive MIMO-G Wireless LAN Adapter User's Manual iv. Display certicate information in use client certicate page. v. Click OK. The result will look like the below figure. - 55 AirLive MIMO-G Wireless LAN Adapter User's Manual 3. TTLS: i. [. . . ]