User manual AIRLIVE SNMP-FSH2602MG V2

[. . . ] SNMP-FSH2602MG v2 24 + 2-port Mixed Gigabit SNMP Managed Switch User's Manual Copyright and Disclaimer Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user's guide. However, we are not liable for the inaccuracies or errors in this guide. All information is subject to change without notice All Trademarks are properties of their respective holders. AirLive SNMP-FSH2602MG v2 User's Manual Table of Contents Table of Contents 1. [. . . ] Click "Apply" button to restore configuration file. TFTP Backup Configuration You can save current EEPROM value from the switch to TFTP server, then go to the TFTP 54 AirLive SNMP-FSH2602MG v2 User's Manual 4. Web Management in SNMP-FSH2602MG v2 restore configuration page to restore the EEPROM value. Click "Apply" button to restore configuration file. 4. 7 Factory Default Reset Switch to default configuration, default value to as following configuration: Default IP address: 192. 168. 10. 1 Default Gateway: 192. 168. 10. 254 Subnet mask: 255. 255. 255. 0 The other setting value is back to disable or none. Once resetting to factory default successfully, Switch will ask user to reboot the Switch, please click "reboot" button to reboot the Switch. 55 AirLive SNMP-FSH2602MG v2 User's Manual 4. Web Management in SNMP-FSH2602MG v2 4. 8 System Reboot Reboot the Switch in software reset. Click "Apply" button to reboot the switch. 4. 9 Panel List Display the Switch panel GUI. When the Switch is in stacking status, it displays the slaves panel GUI. You can click the port on the panel GUI to check port current information. 4. 10 IP Stacking This function allows Switch to stack up to 8 stackable switches as a unit group. Before configuring the stacking function, make sure all stack switches are in the same network. When configure stacking function, please must configure the master switch first. After stacking group has set up, all slave switches are configured through master switch. You still can directly access to slave switch, but all functions are read and view only. To remove the switch from stacking group, you must remove the salve switch first. When all slave switches are removed, and then you can remove the master switch from stacking group. If you remove the master switch before slave switch, go to slave switches one by one and use console configuration to re-configure the switch 56 AirLive SNMP-FSH2602MG v2 User's Manual 4. Web Management in SNMP-FSH2602MG v2 configuration or you re-configure one of the slave switched as the master by console interface. Disable: It means the switch doesn't belong to any stacking group or stacking function is disabled. Master: It means the switch is the leader (master) in the stacking group. The master switch can control all the slave switches in stacking group. To configure the slave switch that you must access by the master switch. System Information: Enter system information in box. 57 AirLive SNMP-FSH2602MG v2 User's Manual 5. Console Management in SNMP-FSH2602MG v2 In this chapter, we will explain features that are available through console. [. . . ] A standard protocol for sending files between computer over a TCP/IP network and the internet. IGMP Snooping Internet Group Management Protocol. It is a Layer 3 protocol to report IP multicast memberships to neighboring multicast switches and routers. IGMP Snooping is a feature that allows an Ethernet Switch to "listen in" on the IGMP conversation between hosts and routers. When IGMP snooping is enabled in a switch, it prevent hosts on a local network from receiving traffic for a multicast group they have not explicitly joined. [. . . ]