User manual AIRLIVE P-203N

[. . . ] P-203N 3 Ports Wired Print Server User's Manual COPYRIGHT Copyright ©2006/2007 by this company. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. FCC COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. DISCLAIMER This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. [. . . ] The rp= entry should correspond to the port name of the remote printer. The values should be one of lpt1, lpt2 or lpt3 depends on the printer port. The print server should now be available for printing from your Unix host. 44 AirLive P-203N User's Manual 7. 7. 1 Print Server Configuration Utility Introduction This chapter introduces print server's system configuration utility in Windows environment. This utility is automatically installed during Windows Administrator Utility installation procedure - refer to section 3. 2 and 3. 3. This utility provides the most complete management and configuration functions on the print server side. This utility only provides configuration functions for print server itself; it does not include configuration functions for client side or other file server or NetWare server in the network environment. The Configuration Utility provides the following configuration and management functions: Search Print Server: Search All Available Printer Servers on the Network. System Configuration: Print Server Network Ability Setting and Firmware Upgrade. Report: List the Status of All Available Print Servers on the Network. We will explain each function separately in the following section. 45 AirLive P-203N User's Manual 7. 2 Search for All Available Print Server Every time when you run print server's configuration utility, click the "Search" icon on the tool bar. The configuration utility will delay for several seconds because the utility is using system's available network protocols to search for all print servers on the network. All available print servers will be listed under "Print Server Group" on the left side of the window. You must select the print server you would like to configure from the list. The system will, at the same time, display the selected print server's status on the right side of the window. 46 AirLive P-203N User's Manual 7. 3 Status of Print Server Click "Status" icon on the tool bar, the status of the current selected print server will be showed on the right side of the window. The information of the print server displayed are MAC ID, Model Type, Firmware Version, status of each printer port, NetWare file server name, NetWare file server polling interval, NetWare printer queue names, IP address, subnet mask, default gateway, AppleTalk printer type, AppleTalk zone and print server printing ability. . . etc. You can refresh the print server's status by pressing the "Refresh" button . You can restart the print server by pressing the "Reboot" button . 47 AirLive P-203N User's Manual 7. 4 Setup the Print Server Click "Setup" icon on the tool bar, the setup items of the current selected print server will be showed on the right side of the window. A screen will pop up to verify "User Name" and "Password" of the print server. The default values are as follows. User Name: admin Password: airlive 48 AirLive P-203N User's Manual 7. 5 General Configuration Double Click "General" icon and the General configuration window will pop-up. You also can configure the "Print Server Name", "SMB Group Name", "User Name" and "Password" here. You can use this name to identify the print server when you are searching for the print server by the administration and client utilities. User Name / Password is used to authenticate the administrator by the Web administration tool. 49 AirLive P-203N User's Manual 7. 6 TCP/IP Configuration Double Click "TCP/IP" icon and the TCP/IP configuration window will pop-up. You can configure the print server to automatically get IP from DHCP server or manually specify static IP. [. . . ] After installation, the printer model will be added to the list. 98 AirLive P-203N User's Manual Step7. "Next". Choose to set the print whether as a default printer or not. Click "Finish". 99 AirLive P-203N User's Manual 100 AirLive P-203N User's Manual 11. LPR Setting in MAC OS LPR Printing (Line Printer Remote technology) allows Macintosh computers to connect to printers via TCP/IP. To enable LPR Printing in Macintosh, please follow the procedures below. [. . . ]