User manual AIKO FP-PL4281 MANUAL SERVICE

[. . . ] Display Type Model Name Native Resolution & Frequency Input Voltage 50/60Hz 50/60Hz 50/60Hz 42"SD NP-42S5 42"HD NP-42H5 50"HD NP-50H5 852 X 480 @ 60Hz AC100V ~ 240V, 1024 X 768 @ 60Hz AC100V ~ 240V, 1366x768 @ 60Hz AC100V ~ 240V, 2. 2 Input/Output Terminal HDMI HDMI Input Jack x1 (Type A) RCA Jack(L+R) × 1 RGB Input D-Sub 15-pin Jack ×1 3. 5MM STEREO Jack(L+R) × 1 RCA(YPbPr/YCbCr) Jack × 2 RCA(L+R) Jack × 2 RCA Jack(L+R) × 1 Mini DIN S-terminal × 1 RCA Jack × 2 F-Type × 1 3. 5mm Jack × 1 Component Input Audio Line Output (Analog) S-Video Input Composite Input Antenna Input RS-232C 3. INPUT SIGNAL INTERFACE 3. 1 HDMI Interface HDMI Input Connector Type A Connector Pin Assignment Type A Female Contacts Pin 1 TMDS Data 2+ Pin 2 TMDS Data 2 Shield Pin 3 TMDS Data 2- Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 TMDS Data 1+ TMDS Data 1 Shield TMDS Data 1TMDS Data 0+ TMDS Data 0 Shield TMDS Data 0TMDS ClockTMDS Clock Shield TMDS ClockCEC Reserved(N. C. on device) SCL Pin 16 SDA Pin 17 DDC/CEC Ground Pin 18 +5V Power Pin 19 Hot Plug Detect Sync Signals Digital RGB : TMDS (Video + Audio) Audio - 48kHz / 2 Channel (L + R) DDC 1/2B Audio Input Connector EDID 1. 3 RCA (L+R) Jack 3. 2 RGB Interface RGB Input Connector Audio Input Connector D-Sub 15-Pin Cable Connector Pin out D-Sub 15-Pin Jack (Female) 3. 5mm Stereo Jack Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Red analog Signal Green analog Signal Blue analog Signal GND GND GND for Red signal GND for Green signal GND for Blue signal NC GND GND SDA (Input only) H-Sync or composited H/V Sync Signal V-Sync SCL (Input only) RGB Signals RGB Signal Impedance RGB Audio Input Level RGB Audio Output Level RGB Sync Signals DDC 1/2B 700 mV full scale 75 Ohms 0. 5V[rms] (L+R) 0. 5V[rms] (L+R) TTL 2. 2k ohm internal pull-up resistors. PLASMA DISPLAY PANEL (PDP) SPECIFICATIONS 6. 1 42" SD Specifications Panel Type Number of Pixels Pixel Pitch Cell Pitch Display Area Outline Dimension Pixel Type Number of Gradations Aspect Ratio Peak Brightness Contrast Ratio(in Dark Room) Life-time 42V7 852(H) × 480(V) pixels (1pixel = 3 RGB cells) 1. 080 mm (H) × 1. 080 mm (V) 0. 320 mm (H) × 1. 080mm (V) 920. 1mm (H) × 518. 4mm (V) ± 0. 5mm 1005(H) × 597(V) × 60. 6(D) ± 1mm RGB Closed type (R)1024 × (G)1024 × (B)1024 16:9 Typical 1, 500cd/ Typical 10, 000:1 More than 60, 000 Hours of continuous operation 6. 2 42" HD Specifications Panel Type Number of Pixels Pixel Pitch Cell Pitch Display Area Outline Dimension Pixel Type Number of Gradations Aspect Ratio Peak Brightness Contrast Ratio(in Dark Room) Expected Life-time 42X3 1024(H) × 768(V) (1pixel=3 RGB cells) 0. 900 mm (H) × 0. 676 mm (V) 0. 300 mm (H) × 0. 676 mm (V)(Green Cell basis) 920. 1mm (H) × 518. 4mm (V) ± 0. 5mm 1005(H) × 597(V) × 60. 6(D) ± 1mm RGB Closed type (R)1024 × (G)1024 × (B)1024 16:9 Typical 1, 500cd/ Typical 10, 000:1 More than 60, 000 Hours of continuous operation 6. 3 50" HD Specifications Panel Type Number of Pixels Pixel Pitch Cell Pitch Display Area Outline Dimension Pixel Type Number of Gradations Aspect Ratio Peak Brightness Contrast Ratio(in Dark Room) Expected Life-time 50X3 1366(H) × 768(V) (1pixel=3 RGB cells) 0. 810 mm (H) × 0. 810 mm (V) 0. 270 mm (H) × 0. 810 mm (V)(Green Cell basis) 1106. 5mm (H) × 622. 1mm (V) ± 0. 5mm 1190(H) × 700(V) × 58(D) ± 1mm RGB Closed (Well)type (R)1024 × (G)1024 × (B)1024 16:9 Typical 1, 000cd/ Typical 8, 000:1 More than 60, 000 Hours of continuous operation 7. [. . . ] - Check for any distortion or noise on the screen. < Crosstalk> (9) 8-black Crosshatch - Check the horizontal/vertical lines for any loss. - Check for any distortion or noise on the screen. <8-black Crosshatch> (10) Display Position < Display position> - Check to ensure that the corresponding areas at the top, bottom, right and left are balanced, based on the vertical line in the center. - Check if the central horizontal line matches the physical center of the PDP panel. - Check for any distortion or noise on the screen (11) SMPTE RP-133 - Check the cross patterns for any loss. - Check for any distortion or noise on the screen. ] < SMPTE RP-133> (12) 256Gray+RGBW Color Bar - Check each color bar for the boundary nesting. - Check if any horizontal or vertical noise occurs. <256gray+RGBW color bar> Patterns (1) to (5) are based on signals from ShibaSoku (TG 848). Patterns (1) to (5) are applied to VIDEO, S-VIDEO, SCART or TV Input. Patterns (6) to (12) are applied to RGB, DIV or Component Input. 2) Speaker Output Item Signal/Noise Ratio Condition Sound: 1KHz, MODULATION over 30% Picture: Black 50mW output Signal/Buzz Ratio Max. Audio output Sound : 1KHz, MODULATION over 30% Picture: COLOR BAR 50mW output Sound : 1KHz, 100% MODULATION Volume : Max. 9 W or higher A resistance of 8 35dB or Higher 37dB or Higher Standard 3) Input Input Condition Digital RGB HDMI Input Audio Audio In Video Input V Signal Y Signal S-Video Input No distortion or noise on the screen C Signal Audio In Y Component Input Pb, Pr Audio In R, G, B R, G, B Input H, V Audio In Antenna In RF Signal No distortion or noise on the screen No distortion or noise in the audio output No distortion or noise on the screen No distortion or noise in the audio output No distortion or noise on the screen No distortion or noise in the audio output No distortion or noise in the audio output No distortion or noise on the screen No distortion or noise in the audio output No distortion or noise on the screen Standard Per Video Signal Cross-Talk Level - There should be no interference from the signals of other terminals when all input terminals are provided with the appropriate signals. 7. 3 Inspection of Circuit Functions 1) LED 0n/Off Test (1) Check if the red LED indicating the standby status lights is out when connected to the power. (2) Check if the green LED indicating the operation status lights is out when the power switch is turned on 2) KEY / REMOCON Test Press the front keys and the MENU key on the remote control and check if they are operating properly as below 3) TV Input (1) Use an RF Cable to connect the TV output signals to the TV Input terminal. (2) Turn on the power by pressing the front key or the POWER key on the remote control. (3) Press the front key or the INPUT key on the remote control then select TV Input. Channel Color System Air/Std/Hrc/Irc Auto Search Add/Delete Fine Tune (5) Choose Color TV Video System (Auto, NTSC-M, PAL-M, PAL-N) from System Menu. (6) Choose TV broadcasting from "Air/Std/Hrc/Irc". (7) Check that broadcasting of TV is accordant with TV frequency by pushing "Auto Searching" in remocon. (9) Choose "Add" or "Delete" through Add/Delete Key. (11) Check that changing channel is O. K through pushing "control key" or "-CH+" of remocon. (12) Check that audio function is O. K through "Control Key" or "-CH+" of remocon. (13) Check that all of each function is O. K through putting "closed caption" Mode of "set up" on Menu screen. (14) Check that all of each function is O. K through putting "V chip" mode in "set up" on Menu. 4) VIDEO Input (1) Connect the video input signals to the VIDEO Input terminals using the RCA cable. (2) Turn on the power by pressing the front key or the POWER key on the remote control. (3) Select "Video" port using front panel button or Remote Controller. Input Sources TV . [. . . ] 5 Menu CHANNEL Function Color System Air/Std/Hrc/Irc Auto Search Add/Delete Fine Tune Default AUTO AIR N/A N/A N/A REMARK < Chart 2 > Picture, Window, Sound, Setting Menu is the same condition as Chart 1. TV Broadcasting System (PAL ) PAL B/G Country Afghanistan Albania Algeria Australia Austria, Azores Bahrain Bangladesh Brunei, Cameroon Canary Islands Cape Verde Cyprus, Denmark Fiji, Finland Germany, Grana Iceland, India Indonesia, Israel Italy, Jordan Konya, Kuwait Laos Liechtenstein Madeira Majorca islands Malaysia, Malawi Mozambique Netherlands New Zealand Nigeria, Norway D/K China Korea (North) N Argentina Paraguay Uruguay M Brazil I Angola Botswana Hong Kong South Africa Zanzibar Oman Pakistan Palestine Papua new guinea Portugal, Qatar Sierra Leone Singapore, Spain Sri Lanka Sudan, Swaziland Sweden, Switzerland Thailand, Turkey Uganda Yemen United Arab Emirates Zambia, Zimbabwe TV Broadcasting System (SECAM/NTSC ) SECAM B/G Country Egypt Iran Iraq Lebanon Lesotho Libya Mauritania SaudiArabia Tunisia Bulgaria CIS(USSR) Congo Czech republic Burkina Faso Burundi Djibouti French Guiana Gabor Guadeloupe Guinea Guinea-Bissau Guiana D/K Hungary Ivory coast Madagascar Matinique Mongolia Poland Reunion Rumania Slovakia Gambia I L France Tahiti Togo Zaire New Caledonia Niger Rwanda Senegal NTSC M Country KOREA USA CANADA JAPAN PDP TV Firmware Update A. - Connect the D-Sub Conn of cable of Main FW update being provided to PC Connect 3. 5mm Jack to PDP-TV. Remove Power Cord The position of Port of PDP-TV Back / Update cable 3. Select "Folder" which is put firmware in Flashexpress. 6. Connect Power Cord by pushing "Flash" button. Connect Power Cord of your TV . Updating firmware is done completely. [. . . ]