User manual AEG IDE84242IB

[. . . ] EN Instruction on mounting and use DE Montage- und Gebrauchsanweisung DA Bruger- og monteringsvejledning FI Asennus- ja käyttöohjeet FR Prescriptions de montage et mode d'emploi IT Istruzioni di montaggio e d'uso NL Montagevoorschriften en gebruiksaanwijzingen NO Instrukser for montering og bruk SV Monterings- och bruksanvisningar Strictly observe the instructions in this manual. No liability will be assumed for any problems, damage or fires caused by failure to comply with the instructions in this manual. The device is intended for domestic use only, to cook food and extract the fumes generated by cooking. The manufacturer declines any liability for inappropriate use or incorrect setting of the controls. [. . . ] Using wall-mounted exhaust pipes and holes with a smaller diameter may reduce the efficiency of extraction and drastically increase noise levels. Use ducting with the least possible number of curves Avoid drastic changes in the ducting diameter. 8 The extracted air will be filtered in special grease filters and odour filters before being sent back into the room. The product is supplied with all parts necessary for standard installation, with the air outlet positioned in the front part of the cabinet plinth. Four high-performance ceramic activated carbon filter packs are already supplied with the product. Ceramic filters are innovative modular carbon filters, which are regenerating (see the Maintenance - Activated carbon filters section of this manual). Their chemical-physical properties allow extremely efficient odour absorption and high mechanical resistance. For more information, see the page relative to the filtration version (in the illustrated part of this manual). The electrical and mechanical installation must be performed by qualified personnel. The household appliance is designed to be built-in to a worktop (3-6 cm thick) The minimum distance between the hob and the wall must be at least 5cm at the front and at least 10 cm on the sides. 3 - Disconnect the device from the electrical network -The installation must be performed by professionally qualified personnel familiar with the applicable installation and safety standards. Check that the product is the right size for the installation location. Check for accessories inside the packaging (placed there for ease of transport) such as bags containing screws, the warranty card, etc. Also check that there is a power socket near the installation area Preparing the cabinet for installation: - The product cannot be installed above cooling appliances, dishwashers, heaters, ovens, washing machines and dryers. - Cut the cabinet before inserting the hob and carefully remove shavings or sawdust. IMPORTANT: use a single component adhesive sealant (S), resistant against high temperatures up to 250°; prior to installation, the surfaces that need to be glued must be carefully cleaned, removing all substances that may compromise adhesion (e. Release agents, preservatives, grease, oils, powders, old adhesive residue, etc. ); the sealant must be evenly distributed along the entire perimeter of the frame; after gluing, leave to dry for approximately 24 hours. Failure to install screws and fasteners in accordance with these instructions may result in electrical hazards. Note: to ensure the correct installation of the product, it is recommended to tape the pipes using an adhesive with the following characteristics: - soft elastic PVC film, with an acrylic-based adhesive - which complies with DIN EN 60454 regulations - flame retardant - excellent resistance against wear - resistant against temperature fluctuations - can be used in low temperatures Control panel Note: To select the commands, simply touch (press) the symbols representing them ON/OFF of the hob / extractor fan for hob View extraction speed (power) Cooking zone : RL = rear left FL = front left RR = rear right FR = front right USING THE HOB Before you begin, it is important to know: All functions of this hob are designed to comply with the most stringent safety regulations. for this reason: · Some functions will not be activated, or will be automatically deactivated, in the absence of pots on the burners or when they are poorly positioned. In other cases the activated functions will be automatically deactivated after a few seconds when the specific function requires a further setting that has not been selected (e. [. . . ] If the fault persists after the above checks, contact the nearest Customer Service. ) Fabrikanten fralægger sig ethvert ansvar for ikke tilladt brug, eller for forkerte indstillinger af betjeningsanordningerne. Emhætten må ikke bruges eller efterlades hvis pærerne ikke er korrekt monteret, for at forebygge risiko for elektrisk stød. Brugeren, der sørger for at bortskaffe dette produkt på korrekt måde, medvirker til at forebygge de potentielt negative indflydelser for miljø og sundhed. [. . . ]