User manual AEG CS MP300

[. . . ] Installation Take out screw before installation DIN Front-Mount (Method A) Installing the unit Removing the unit DIN Rear-Mount (Method B) Using The Front Panel Wiring Connection Operation Location of keys Switching on/off the unit Faceplate Release Sound adjustment Loudness Display Equalization Flashing LED Reset function Radio operation Switching to radio mode Selecting the frequency band Selecting station Automatic memory storing & program scanning Station storing 3 3 3 3 4 5 6 7 8 8 9 9 9 10 10 10 11 11 11 11 11 11 11 11 14 MP3 operation 14 Switch to CD (MP3) mode Ejecting a disc 14 Selecting tracks in single step 14 14 Selecting directory up/down 14 Pausing playing Previewing all tracks 14 Repeating the same track 14 Playing all tracks in random 14 Selecting tracks by 14 AMS/MP3 button 15 Display information 16 Disc notes 17 Specification 18 Trouble shooting Warranty. RDS (Radio Data System) operation 12 CD operation 13 Switching to CD mode Selecting tracks Pausing playing Previewing all track Repeating the same tracks playing all track in random 13 13 13 13 13 14 Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. [. . . ] - MASK ALL mode: Masked the AF which has different PI and NO RDS signal with high field strength. - BEEP 2'nd mode: The beep is only generated when all allowed double key is pressed long (1 sec). DISPLAY Press DSP button (15) to operate as the conversion of each display mode as follows: - In case of receiving a RDS station In radio mode: ->PS ->CT ->FREQ ->PTY -> In CD mode: ->CD ->CT ->PS ->FREQ ->PTY -> - In case of no receiving CT or PTY information, the display shows as "NO CLOCK" or "NO PTY". - In case of receiving a non RDS station In radio mode: In CD mode: -> CD -> CT -> FREQ -> "NO PTY" -> Each displaying time is several seconds, and come back to 1st position after several seconds. LIQUID CRYSTAL DISPLAY Exhibit current frequency and activated functions on te display(8) FLASHING LED If the front panel does not install in the main unit, the LED (24) will be flashing. RESET FUNCTION RESET button (25) must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. Note: if press RESET button (25), the unit can't work yet, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the front panel. sELECTING STATION Press MANU/SKIP button(16) or button MANU/SKIP (17) shortly to activate automatic seek function. Press for several seconds until "MANUAL" appears on the display, the manual tuning mode is selected. If both buttons have not been pressed for several seconds, they will return to seek tuning mode and "AUTO" appears on the display. AUTOMATIC MEMORY STORING & PROGRAM SCANNING - Automatic memory storing Press AS/PS button (18) for several seconds, the radio searches from the current frequency and checks the signal strength until one cycle search is finished. And then 6 strongest stations are stored into the corresponding preset number button. - Program scanning Press AS/PS button (18) shortly to scan preset station, When the field strength level is more than the threshold level of stop level, the radio is holding at that preset number for several seconds with release mute, then searches again. STATION STORING Press any one of the preset buttons (14) (1 to 6) to select a station, which had been stored in the memory. Press this button for several seconds (until 2ND beeps come out), current station is stored into the number button. RADIO OPERATION SWITCHING TO RADIO MODE Press MOD button (6) shortly to select radio mode, the radio mode appears in the display together with the memory band and frequency. RDS (RADIO DATA SYSTEM) OPERATION - Setting RDS mode Press AF/REG button (3) and release immediately to switch on or off RDS mode. ALARM will be displayed when an emergency broadcasting is received, meanwhile sound output level will be adjusted to the preset output level automatically when the volume control is set at minimum. - Regional Program Operation Press AF/REG button (3) for several seconds to switch on or off region mode. In above operation, a customer listens to a wrong program or mute sound for a while. EON TA LOCAL mode When the filed strength level of EON linked is less than threshold level, the radio does not switch that station, and a customer can hardly listen to any disturbances. [. . . ] DISPLAY INFORMATION Press DSP button(9) to show the following information, such as the clock, ID3 TAG (if available: song title, directory name, artist name, other contents. Do not stick paper or tape, etc, onto the label side or the recording side of any discs, as it may cause a malfunction. Be sure to use discs with following marks only for the unit to play: C. The disc must be in the ISO9660 level 1or level 2 format, or Joliet or Romeo in the expansion format. [. . . ]