User manual AEG-ELECTROLUX T86585IH

[. . . ] Machine settings Technical data Consumption values Hints for test institutes Installation Environment 5 5 8 9 10 10 12 17 26 29 36 40 42 43 43 44 50 Service 52 important safety information electrolux 5 Operating Instructions Important safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. General safety · It is dangerous to alter the specifications or attempt to modify this product in any way. [. . . ] The display will show 0'and then the duration of the selected programme. The amount of time remaining until the programme is set to start is continuously displayed (e. g. 30' etc). Setting child lock The child lock can be set to prevent a programme being accidentally started or a programme in operation being accidentally changed. The child lock can be activated or deactivated by holding down the Option and OK buttons simultaneously for 5 seconds. ­ Before programme is started: Appliance cannot be used ­ After programme is started: Programme in operation cannot be changed icon appears in the display to indicate that the child safety device is actiThe vated. The child safety device is not deactivated once the programme comes to an end. If you want to set a new programme, you must first deactivate the child safety device. Starting the programme Press the Start/Pause button. The programme is started. 24 electrolux daily use The programme progress is shown in LCD by appropriate set of icons. From left to the right, from IRON DRY to ANTI-CREASE icon depends on the drying cycle chosen. in case of CUPBOARD programme the following status icons are visible: . When appropriate part of drying cycle is accomplished dash becomes steady and appears flashing under next status icon. Changing programme To change a programme which has been selected by mistake once the programme has started, first turn the programme selector to OFF Aus and then reset the programme. The programme can no longer be changed directly once the programme has started. If nevertheless there is an attempt to change the programme on the programme knob, the programme progress display and the maintenance indicators flash. Press both journals of the large mesh filter into the brackets on the loading door until they snap into place. Press against the large mesh filter until it locks into the interlock. If the fine strainer is not fitted, the large mesh filter will not snap into place and the loading door cannot be closed. Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished. Emptying the condensate tank Empty condensate tank after every drying cycle. 32 electrolux care and cleaning If the condensate tank is full, an active programme will break off automatically and the EMPTY CONTAINER icon on the display will light up. In order to continue the programme, the condensate tank must first be emptied. The condensate is not suitable for drinking or for preparing foodstuffs. 1. 2 1 Take out drawer containing condensed water container completely 1 and pull up the condensed water container's drainage pipe as far as it will go 2. If the programme has been interrupted as a result of the condensate tank being full: Press the Start/Pause button to continue the drying cycle. The condensate tank has a volume of approx. This is sufficient for around 7kg of laundry which has previously been spun at 1000 revolutions/ minute. care and cleaning electrolux 33 The condensate can be used as distilled water, e. g. with a coffee filter) to remove any residue and small pieces of fluff. Cleaning heat exchanger If the HEAT EXCHANGER is displayed, the heat exchanger needs to be cleaned. Operating when the heat exchanger is blocked with fluff can damage the dryer. To do this, press the release button on the bottom of the door aperture and open the door in the plinth to the left. Clean fluff from the inside of the door and the heat exchanger front chamber. 4. Turn both lock washers inwards. 34 electrolux care and cleaning 5. Use the handle to pull the heat exchanger out of the base and carry it horizontally to prevent any remaining water from spilling. To empty the heat exchanger, hold vertically over a washing-up bowl. Do not use sharp objects to clean. [. . . ] Use an appropriate tool and exert pressure to unfasten locking block D from the snap-on fixture, take out and re-insert on the other side having rotated the block through 180°. Unscrew hinge A from the loading door, rotate through 180°, re-insert on the opposite side and screw down. Re-insert cover plates B and C on the opposite site having first rotated them through 180°. E G F E F G 7. Unscrew cover plates E from the front of the machine, rotate through 180°, screw on the opposite side. [. . . ]