User manual AEG-ELECTROLUX RE125107

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX RE125107. We hope that this AEG-ELECTROLUX RE125107 user guide will be useful to you.


AEG-ELECTROLUX RE125107 : Download the complete user guide (1422 Ko)

You may also download the following manuals related to this product:

   AEG-ELECTROLUX RE125107 (1859 ko)

Manual abstract: user guide AEG-ELECTROLUX RE125107

Detailed instructions for use are in the User's Guide.

[. . . ] Such instruction should emphasize: - the need for care and concentration when working with ride-on machines; - control of a ride-on machine sliding on a slope will not be regained by the application of the brake. The main reasons for loss of control are: a) insufficient wheel grip; b) being driven too fast; c) inadequate braking; d) the type of machine is unsuitable for its task; e) lack of awareness of the effect of ground conditions, especially slopes; f) incorrect hitching and load distribution. Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect. Before attempting to start the engine, disengage all blade attachment clutches and shift into neutral. [. . . ] With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Remove the two (2) 3/8 nuts and flat washers from the bolts at the tractor back plate. Install the two upper support brackets through the back plate and to the chassis, using the 10 x 19 mm (3/8"x3/4") carriage bolts and locknuts supplied. Assemble both support brackets to the outside of the baggger support tube using two each 3/8 x 63, 5mm hex bolts13/32" I. Using the nuts and flat washers removed from tractor back plate, install the bagger support tube to the back plate as shown. This will allow the discharge chute to float with the mower deck when moving on uneven terrain. NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger together. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts. â· Assemble front and lower bagger tubes using four (4) 1/4 x 50, 8mm carriage bolts and lock nuts supplied. â· Assemble front and upper bagger tubes using four (4) 1/4 x 50, 8mm carraige bolts and lock nuts supplied. Slide the bagger dump handle through the hole in the bagger top, install the clevis pin and secure with retainer spring. The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards. SAE 5W-30 oil should be used during the winter (below freezing point). Make sure that the cutting unit is in the transport position (top position) and that the lever for connection/disconnection of the cutting unit is in the disconnection position. If the engine will not start, wait about 10 seconds before the next try. Let the ignition key return to the "ON" position when the engine has started and push in the choke control as soon as the engine is running smoothly. Move motion control lever to full forward position and hold for five (5) seconds. engage transmission by placing freewheel control in driving position. Drive tractor forward for approximately five feet then backwards for five feet. To ensure proper operation and performance, it is recom mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor. The machine is equipped with a safety switch which immediately breaks the current to the engine if the driver leaves the seat with engine running and with the connection/disconnection lever in position "connection". [. . . ] Remove the two rear retainer springs (2) and knock off the axle taps with a hammer. Work off the belt from the unit's left pulley and then from the other wheels. In the direction of travel Check that the air pressure is correct in all four tires. To achieve best cutting results the cutting unit's front edge (B) should be about 10 mm (0. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX RE125107




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX RE125107 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.