User manual AEG-ELECTROLUX PE9039-M

[. . . ] PE 9038-m Fully automatic espresso coffee machine Operating and Installation Instructions ENGLISH CONTENTS 1. 17. Safety instructions Description of the coffee machine Description of the control panel: touch control Instructions for the first use of the machine Making Coffee Hot water Steam Programming the amount of coffee beans to be grinded Programming the volume of coffee dispended in the cup If you wish to reset the standard values Signals and alarms Coffee menus Cleaning Installation Something not working. . . . Technical specifications After-sales Service, spare parts and guarantee 2/35 1. SAFETY INSTRUCTION Please read this instruction book before using the appliance and retain for future reference. [. . . ] This indicates that the machine is locked in position. 14/35 STAND-BY MODE · · Once powered and inserted into the cabinet, the machine is in stand-by mode: this will be signaled by the on/off LED blinking. Press the on/off control to switch on the machine: the start LED will be illuminated. · To come back to the stand-by mode, press the on/off control once again. On start-up, the machine initiates the pre-warming phase for the first 3 minutes. During this phase the ON/OFF LED will blink quickly and the machine will be not able to execute any operation. Then the LED blinks slowly and the machine is ready to operate. CAUTION: 15/35 5 MAKING COFFEE · Press the control corresponding to the desired selection. · · Press the start control within 10 seconds and the machine will make the coffee selected. The machine will stop automatically CAUTION: the desired function will be disabled if the start control is not pressed within 10 seconds. To improve the result, gently beat the jug a little on the table after that the foam is ready. 18/35 8 · · · PROGRAMMING THE AMOUNT OF COFFEE BEANS TO BE GRINDED This espresso machine has already been calibrated in factory to dispense the ideal measure of ground coffee for one cup of espresso. However this quantity of ground coffee can be increased or reduced, then the selected measure is stored. The programmable measure of ground coffee refers to both the espresso selection and to regular coffee selection. Put the machine on stand-by mode as described. · Keep the start control pressed for 10 seconds. · Some LEDS will flash, working as indicators, (the more the LEDS are illuminated the greater the quantity of coffee). Before adjusting make a note of the original setting so that the machine can be reset to the factory settings if required. · To increase or decrease the quantity of ground coffee just press the "espresso" control to decrease and "regular coffee" control to increase. 19/35 · Once you have modified the coffee ground quantity, press the start control for 10 seconds and the machine will automatically save the quantity desired and it will return to stand-by mode. CAUTION: the correct grinding time can change if a different kind of coffee is used. If any unpressed coffee powder is found when emptying the "used" coffee drawer, it means that the grinding time is too long and should be decreased. The "exhaust" coffee pods in the "used" coffee drawer can help to achieve a correct regulation of the grinding-time. The coffee pods must be 1 cm in thickness: this is the correct coffee quantity. If its thickness is lower, it means that the grinding time is too short and should be increased. IMPORTANT: Increasing or decreasing the grinding time can change the coffee taste. A stronger coffee taste and a rich aroma can be obtained by slightly increasing the programmed time. A weaker coffee can be obtained by slightly decreasing the programmed time. 20/35 9 · PROGRAMMING THE VOLUME OF COFFEE DISPENSED IN THE CUP The volume of coffee dispensed can be adjusted as desired as follows: · Press the espresso control. · Keep the start control pressed until the programme starts (approximately 5 seconds); the start control LED flashes. · When the desired quantity of coffee has been dispensed, press the start control. The machine will stop the cycle and the coffee measure will be stored automatically on the correspondent selection. 21/35 10 IF YOU WISH TO RESET THE STANDARD VALUES RESETTING STANDARD VALUES · This coffee machine is calibrated in the factory to make the optimum Italian espresso, the values set for the espresso coffee distribute 30 cc, the values set for the regular coffee is 80 cc. · if the standard values have to be reset from the stand-by control switch on the machine then press both the on/off and hot-water controls at the same time for 5 seconds. · All the LEDs will briefly illuminate to indicate the factory values have been reset. · Press the ON/OFF control. Each selection will use the factory values. N. B. : Only the quantity of water required for each cup of coffee is reset. 22/35 11 SIGNAL AND ALARMS WATER REFILL INDICATOR · This machine has a sensor which detects when the water reservoir is empty. The machine will not operate until the water reservoir is refilled. VOLUMETER COUNTER FAULT · This machine has a volumeter counter which detects the amount of water distributed by the machine. If the water reservoir is empty or if the volumeter counter is faulty the reservoir empty led will blink and the machine will not operate. [. . . ] The width of the housing unit the coffee machine depends on the thickness of the cabinet's sides. six side plates (four being 2 mm thick and two 1 mm thick) are provided to compensate for the different possible measures. 31/35 · hey should be used to compensate for the internal width of the compartment, leading to a width of 560/570 mm. · Fix the U base plate inserting 4 selfthreading screws into the 4 front holes of the same plate. Then screw the telescopic runners to each side with the remaining 8 self-threading screw. · Insert the machine into the housing by coupling the machine to the runners fixed to the sides of the carcass. 32/35 · Slide the machine into the cabinet until the "click" indicates that it is locked into Position. 15 SOMETHING NOT WORKING. . . . . If this machine does not work, please make sure that the fault is not due to: 1. no power no water in the reservoir. If the power cable is damaged or the machine needs servicing, please contact the nearest SERVICE FORCE CENTRE 16 TECHNICAL SPECIFICATIONS · · · · · · · · · · · · Width Depth Height Capacity of water reservoir Net weight Gross weight Supply voltage Rated power Power absorbed by the heating element Power absorbed by the pump Working pressure Fuse 594 mm 475 mm 378 mm 2. 5 l 28 kg 31 kg 230 V 2000 W 1700 W 50 W 12 bar 13 A 33/35 17 AFTER-SALES SERVICE, SPARE PARTS AND GUARANTEE SERVICE & SPARE PARTS If you wish to purchase spare parts or require an engineer, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your telephone call will be automatically routed to the Service Centre covering your postcode area. [. . . ]