User manual AEG-ELECTROLUX HK955070FB

[. . . ] Do not put cutlery or saucepan lids on the cooking surface, as they can become hot. Overheated fats and oils can ignite very quickly. Correct operation Always monitor the appliance during operation. Do not put or keep very flammable liquids and materials, or fusible objects (made of plastic or aluminium) on or near the appliance. · Be careful when you connect the appliance to the near sockets. [. . . ] You must have correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors. · · · · · · · Sticking on the seal · Clean the worktop in the area of the cut-out section. · Bond the sealing tape to the lower edge of the cooking surface along the outer edge of the glass ceramic. When you have cut it to length (add some mm), push the two ends together. Installation 5 Assembly min. 30 mm 6 Description of the appliance Description of the appliance Cooking surface layout 1 2 3 145 mm 145/ 210/270 mm 265 mm 170 mm 180 mm 180 mm 1 2 3 4 5 6 Single cooking zone 1200 W Triple cooking zone 1050/1950/2700 W Oval cooking zone 1400/2200 W Single cooking zone 1800 W Control panel Single cooking zone 1800 W 6 5 4 Control panel layout 1 2 3 4 5 6 12 11 10 9 8 7 Use the sensor fields to operate the appliance. sensor field 1 2 3 4 5 6 7 8 9 10 11 function starts and stops the hob starts and stops the key lock or child lock shows for which zone you set the time shows the time in minutes activates automatic heat-up starts and stops the roasting zone shows the heat setting to set the heat setting starts and stops the outer rings increases or decreases the time selects the cooking zone a lock with an indicator cooking zones' indicators of timer the timer display with an indicator a heat setting display a control bar with an indicator / Operating the appliance sensor field 12 7 function starts and stops STOP+GO with an indicator Heat setting displays Displays show which functions operate Display The cooking zone is off The cooking zone operates Keep Warm The automatic heat-up function is on + digit / / There is a malfunction OptiHeat Control (3 step Residual heat indicator): still cooking / keep warm / residual heat Lock/Child safety function is on The automatic switch off is on Description OptiHeat Control (3 step Residual heat indicator) WARNING!OptiHeat Control indicates the level of the residual heat. Operating the appliance On and Off Touch for 1 second to start or stop the appliance. Automatic Switch Off The function stops the hob automatically and comes on if: · all cooking zones are off . · you cover a sensor field with an object (a pan, a cloth, etc. ) for longer than 10 seconds. · you do not stop a cooking zone or change the heat setting after some time. Automatic Switch Off times Heat setting Stops after 6 hours 5 hours 4 hours 1. 5 hours 8 Operating the appliance The heat setting Touch the control bar at the necessary heat setting. The display shows the heat setting. A / Switching the outer rings on and off You can match the effective heating surface to the size of the cookware. For To switch on the outer ring touch the sensor field / more outer rings touch the same sensor field again. The indicator goes out. The Automatic heat up The Automatic heat up function sets the highest heat setting for some time, and then decreases to the necessary level. To start function touch the symbol and than set the necessary heat setting. To stop the function change the heat setting. 12 11 10 9 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Using the Timer Count Down Timer Use the Count Down Timer to set how long the cooking zone operates for one cooking session. · Selection of the cooking zone: touch again and again until the indicator of a necessary cooking zone comes on. · Starting the Count Down Timer: touch of the timer to set the time ( 00 - 99 minutes). When the indicator of the cooking zone flashes slower, the time counts down. · Changing the Count Down Timer: select the cooking zone with touch or . Operating the appliance 9 · Stopping the timer: select the cooking zone with . · Stopping the sound: touch CountUp Timer (Count up timer) Use the CountUp Timer to monitor how long the cooking zone operates. · Selection of the cooking zone (if more than 1 cooking zone operate): touch again and again until the indicator of a necessary cooking zone comes on. When the indicator of the cooking zone flashes slower, the time counts up, display switches between and time elapsed (minutes) · Checking the elapsed time: select the cooking zone with . · Stopping the CountUp Timer: select the cooking zone with and touch or to switch off the timer. [. . . ] Switch on the signals. There is no signal when you touch panel keys If you tried the above solutions and cannot repair the problem, speak to your dealer or the Customer Care Department. Give the data from the rating plate, three-digit-letter code for the glass ceramic (it is in the corner of the cooking surface) and an error message that comes on. If you operated the appliance incorrectly, the servicing by a customer service technician or dealer will not be free of charge, even during the warranty period. The instructions about the customer service and conditions of guarantee are in the guarantee booklet. Environment concerns 13 Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste. [. . . ]