User manual AEG-ELECTROLUX F65040VI1P

[. . . ] FAVORIT 65040 VI EN DISHWASHER USER MANUAL 2 www. aeg. com CONTENTS 4 6 7 8 10 11 13 15 16 17 18 SAFETY INFORMATION PRODUCT DESCRIPTION CONTROL PANEL PROGRAMMES OPTIONS BEFORE FIRST USE DAILY USE HINTS AND TIPS CARE AND CLEANING TROUBLESHOOTING TECHNICAL INFORMATION ENVIRONMENT CONCERNS Recycle the materials with the symbol . Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. VISIT OUR WEBSITE FOR: - Products - Brochures - User manuals - Trouble shooter - Service information www. aeg. com LEGEND Warning - Important Safety information. [. . . ] If you stop to use the combi detergent tablets, before you start to use separately detergent, rinse aid and dishwasher salt, do these steps: 1. Make sure that the salt container and the rinse aid dispenser are full. Start the shortest programme with a rinsing phase, without detergent and without dishes. Adjust the water softener to the water hardness in your area. On Off 4. Deactivate the appliance to confirm. ENGLISH 11 BEFORE FIRST USE 1. Make sure that the set level of the water softener agrees with the water hardness in your area. Contact your local water authority to know the water hardness in your area. If you use the combi detergent tablets, activate the multitab option. ADJUSTING THE WATER SOFTENER Water hardness German degrees (°dH) 51 - 70 43 - 50 37 - 42 29 - 36 23 - 28 19 - 22 15 - 18 11 - 14 4 - 10 <4 French degrees (°fH) 91 - 125 76 - 90 65 - 75 51 - 64 40 - 50 33 - 39 26 - 32 19 - 25 7 - 18 <7 mmol/l Clarke degrees 64 - 88 53 - 63 46 - 52 36 - 45 28 - 35 23 - 27 18 - 22 13 - 17 5 - 12 <5 Water softener adjustment Manual Electronic 10 9 8 7 6 51) 4 3 2 12) 9. 1 - 12. 5 7. 6 - 9. 0 6. 5 - 7. 5 5. 1 - 6. 4 4. 0 - 5. 0 3. 3 - 3. 9 2. 6 - 3. 2 1. 9 - 2. 5 0. 7 - 1. 8 < 0. 7 2 1) 2 1) 21) 21) 21) 21) 1 1 1 12) 1) Factory position. 2) Do not use salt at this level. You must adjust the water softener manually and electronically. Manual adjustment Turn the water hardness dial to the position 1 or 2. 12 www. aeg. com Electronic adjustment 1. Make sure that the appliance is in setting mode, refer to `SETTING AND STARTING A PROGRAMME'. Press and hold buttons (4) and (5) at the same time until the indicators of buttons (3), (4) and (5) flash. · If you open the door, the display shows the programme duration that decreases with steps of 1 minute. SETTING AND STARTING A PROGRAMME Setting mode The appliance must be in setting mode to accept some operations. The appliance is in setting mode when, after the activation the display shows 2 horizontal status bars. If the control panel shows other conditions, press RESET until the appliance is in setting mode. Starting a programme without delay start 1. The programme starts. 1 Starting a programme with delay start 1. Press the delay button again and again until the display shows the delay time you want to set (from 1 to 24 hours). · If you open the door, the display shows the countdown of the delay start that decreases with steps of 1 hour. When the countdown is completed, the programme starts. 14 www. aeg. com Opening the door while the appliance operates If you open the door, the appliance stops. When you close the door, the appliance continues from the point of interruption. Cancelling the delay start while the countdown operates Press the cancel button until the display shows 2 horizontal status bars. When you cancel a delay start, the appliance goes back to setting mode. [. . . ] Make sure that it assembles correctly under the two guides (C). Assemble the filter (A) and put it into position in filter (B). An incorrect position of the filters can cause bad washing results and damage to the appliance. CLEANING THE SPRAY ARMS Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads or solvents. EXTERNAL CLEANING Clean the appliance with a moist soft cloth. ENGLISH 17 TROUBLESHOOTING The appliance does not start or it stops during operation. [. . . ]