User manual AEG-ELECTROLUX EWT10120W

[. . . ] Good luck ! 4 contents Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 The following symbols have been used in this user guide : Important information about concerning your safety and information on how to avoid damaging the appliance. Information concerning the environment. warnings 5 Warnings These warnings are for the safety of you and others around you. Please read these points carefully before installing and using your appliance. [. . . ] "Err" flashes and the "Start/Pause" pushbutton flashes red for a few seconds then the current cycle display reappears. Selecting the temperature Press the "Temperature" pushbutton repeatedly to increase or decrease the temperature if you want your washing to be washed at a different temperature to the one selected by the appliance. Selecting the spin speed Press the "Spin" pushbutton to change the spin speed, if you want your washing to be spun at a different speed to the one selected by the appliance. You can also select "No spin"*, "Rinse hold"* or "Night silence plus" *. The maximum speeds are : for Cottons and Eco : 1300 rpm (EWT 13320W), 1200 (EWT 12320W), 1000 (EWT 10320W), for Jeans : 1100 rpm (EWT 13320W), 1200 (EWT 12320W), 1000 (EWT 10320W), for Handwash and Wool : 900 rpm (EWT 13320W, EWT 12320W), 1000 (EWT 10320W), for Synthetics, Easy iron, Lingerie and Sport : 900 rpm, for Delicates and Silk : 700 rpm. *depending on model At the end of the programme, if you have selected "Rinse and hold" or "Night silence plus" , you then need to select a "Spin" or "Drain" programme to finish the cycle. "Night silence plus" The washing machine does not empty the water after the final rinse which prevents the washing from creasing. Because there are no spin cycles, the washing programme is very quiet and can be selected at night. In Cotton and Synthetics programmes, the rinsing cycle uses more water. Selecting options You must select the different options after selecting the programme and before pressing the "Start/Pause" pushbutton (see "Programme table"). If one of the options is not compatible with the selected programme, "Err" flashes on the display and the "Start/ Pause" pushbutton flashes red. The symbol for the current cycle and the remaining time appear on the display. 2H If a delayed start has been selected, the countdown appears on the display (hour by hour, then 90, and minute by minute from 60 min). how to run a wash cycle 13 End of the programme The washing machine stops automatically ; the "Start/Pause" pushbutton goes out and "0" flashes on the display. The locking mechanism "snaps" twice to indicate that the lid is open. Remove washing Unplug and close water inlet tap. We recommend leaving the lid and drum open after use to ventilate the water tank. Standby mode If the appliance is on but no commands are selected for 10 min before or after a cycle, it goes into standby mode. The amount of detergent to be used depends on the size of the load, the hardness of the water and how heavily soiled the washing is. If the water contains lime scale (a descaler is recommended) or if the washing is heavily soiled or stained, increase the amount slightly. washing guide 15 You can obtain information on the hardness level of water in your area by contacting your water company or other competent source. For cycles without prewash, they can be added either via means of a dosing ball, or in the detergent compartment. In either International symbols NORMAL WASH Wash at 95°C DELICATE WASH Wash at 60°C case, the wash cycle must be started immediately. Detergent tablets or doses must be placed in the detergent compartment of your appliance's dispenser box. For stain removal before a wash cycle, please refer to manufacturer's recommended amounts and instructions. If you use a detergent to remove stains, the wash cycle must be started immediately. Wash at 40°C Wash at 30°C Hand wash Do not wash BLEACHING Whitewashing (bleach) allowed (cold only and in diluted solution) No whitewashing (bleach) IRONING High temperature (max 200°C) Mid temperature (max 150°C) Low temperature (max 100°C) Do not iron DRY CLEANING Dry cleaning (all common solvents) Dry cleaning (all common solvents except trichlorethylene Dry cleaning (only oil-based solvents and R113) High temperature Mid temperature Do not dry clean DRYING Dry flat Hang dry Dry on clothes hanger Tumble drying permitted Do not tumble dry 16 programmes table / consumption Programmes table Programme / Type of washing Cottons : White or colour, e. g. , normally soiled work clothes, bed linen, table linen, body linen, towels. Synthetics : Synthetic fabrics, body linen, coloured fabrics, non-iron shirts, blouses. [. . . ] · the drum could not stop in the correct position following an unbalanced spin cycle; turn drum manually. The appliance vibrates, is noisy : the wash cycle is much too long : The washing machine stops during a wash cycle : The lid doesn't open at the end of the cycle : The "open drum" light is not on at the end of the cycle : operating problems 21 Problems The E40 error code appears in the display** and the Start/Pause pushbutton flashes red*** : The E20 error code appears in the display** and the Start/Pause pushbutton flashes red*** : Causes · the lid isn't closed properly. · the drainage filter is obstructed, · the drain hose is blocked or bent, · the drain hose is fixed too high (see "Installation" section). · the drainage pump is blocked, · the standpipe is blocked. · the water inlet tap is closed, · the water supply has been cut off. The E10 error code appears in the display** and the Start/Pause pushbutton flashes red*** : The EF0 error code appears in the display** and the Start/Pause pushbutton flashes red*** : · the drainage filter is obstructed, · the anti-flooding security system has been activated, please proceed as follows : - close the water inlet tap, - empty the appliance for 2 minutes before unplugging, - call the after-sales service. · the anti-flooding security system has been activated, please proceed as follows : - close the water inlet tap, - empty the appliance for 2 minutes before unplugging, - call the after-sales service. [. . . ]