User manual AEG-ELECTROLUX ETN1062

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX ETN1062. We hope that this AEG-ELECTROLUX ETN1062 user guide will be useful to you.


AEG-ELECTROLUX ETN1062 : Download the complete user guide (393 Ko)

You may also download the following manuals related to this product:

   AEG-ELECTROLUX ETN1062 (423 ko)

Manual abstract: user guide AEG-ELECTROLUX ETN1062

Detailed instructions for use are in the User's Guide.

[. . . ] GENERAL DESCRIPTION 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) Rear handle Rear hand guard Front handle Front hand guard/chain brake lever Chain tensioner knob/screw Chain tensioner pin Oil tank cap Oil tank inspection gauge Air vents Cable Manual Switch Switch block Chain Drive tooth Cutting link 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) 27) 28) 29) 30) 31) Cutting depth gauge Cutting tooth Bar Chain cover Pinion Chain catcher Bar retaining screws Bar retaining knob / nuts Nose sprocket Guide bar cover guard Spiked bumper Chain tensioner pin housing Lubrication hole Guide groove Oil pump adjustment knob LEGEND: 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) Example of identification label 16) Guaranteed noise level according to directive 2000/14/EC Double insulation CE marking of conformity Protection degree Rated frequency Rated power Alternate current Rated voltage Type Prefix Product code Year of manufacture (last two figures; e. g. 04=2004) Maximum bar length Manufacturer's name and address Serial number Model ENGLISH ­ 1 B. SAFETY PRECAUTIONS MEANING OF SYMBOLS Do not dispose inappropriately of the machine. Always grip the machine with two hands Kickback danger Do not expose to rain or moisture. [. . . ] Wherever possible use a vice or a saw horse to block the wood to be cut; always hold the machine as follows: Grip the front handle with the left hand and the rear handle with the right hand, closing the thumb and other fingers firmly around the handle (during use, the machine could slide forwards or backwards, or create a reverse action, provoking a kickback reaction: holding the machine correctly reduces the risk of loosing control over the tool); Always make sure that the cable/ extension cord is kept behind the user, controlling that it does not create a source of danger for the user or for other persons, and check that it cannot be damaged (by heat, sharp objects, sharp edges, oil, etc); Always assume a stable standing position on both legs; keep the handles dry and clean; during use keep all body parts and clothing well clear of the chain; turn off the switch, wait until the chain has stopped turning, and activate the chain brake lever before putting down the saw; never attempt to cut at heights over shoulder height; always handle the machine with the utmost care; check that the oil level never drops below MIN level, controlling frequently, before and during use; Always remain on the left hand side of the machine during use, and take great care if the bar needs to be inserted in a previously cut slit; remove the bar from the slit when the chain is still in rotation. Each time the work area is changed to another location, disconnect the machine from the main line and activate the chain brake lever. Mount the guide bar cover guard each time before transporting or storage. Always carry the machine by hand with the bar facing backwards, or when transporting the machine in a vehicle, always attach it securely to prevent damage. After use, store the machine in a dry, high place, far from heat sources and out of reach of children. 13. Never use the machine in areas where there are naked flames, inflammable or potentially explosive materials. The kickback reaction consists of a violent upwards-reverse action of the bar towards the user. The chain brake is activated when the front hand guard is pushed forward (the chain is blocked). ENGLISH ­ 5 The chain brake can be activated in two modes: the first using the left wrist by pushing forwards, or when it comes into contact with the brake system as a result of kickback; or by inertia, in the case of particularly violent kickback. When the machine is used with the bar in horizontal position, for example during tree felling, the chain brake offers less protection, because it can be activated by inertia only, since the user's hand is outside the range of action of the front hand guard (fig. 3). N. B. : When the chain brake is activated, a safety switch cuts off all current to the motor. CHAIN CATCHER This machine is equipped with a chain catcher (fig. 4) located under the pinion. This mechanism is designed to arrest the backward chain movement in the case of chain breaking or derailing. In cases where work environments are particularly dirty or dusty, the operations described must be performed more frequently than mentioned in the instructions. Before each use Control that the chain oil pump functions correctly: direct the bar towards a clear surface at a distance of about 20 centimetres; after the machine has run for about a minute, the surface should show clear traces of oil(fig. 1). 1, 2, 3, 4, 5, 6, 7, 8, 9, 12, 13 Check that excessive strength is not needed for activating and deactivating the chain brake. Also check that it is not activated too easily and that it is not blocked. Then check chain brake function as follows: release the chain brake, grip the machine correctly and start up the machine, activate the chain brake by pushing the front hand guard forward with the left wrist or arm but without removing the hand from the handle(fig. 2). If the chain brake is working correctly, the chain should be blocked immediately. ENGLISH ­ 7 Check that the chain is sharpened correctly (See below), in good working condition and that the tension is correct. If the chain is irregularly worn, or if the cutting teeth are only 3 mm high, the chain must be replaced(fig. 3). Check that the switch and switch block function correctly (to be performed with the chain brake released): press the switch and the switch block and control that they return to idle position as soon as they are released; control that it is impossible to press the switch without activating the switch block. Check that the chain catcher and the right hand guard are in correct condition without any visible faults such as damaged material. Every 2-3 hours of use Control the bar condition, if necessary clean the lubrication holes(fig. 4) and the guide grooves(fig. 5) carefully; If the groove is worn or shows signs of deep notching, it must be replaced. Clean the pinion regularly and check that it has not been subject to excess wear(fig. 7). Lubricate the nose sprocket with bearing grease through the hole shown in the illustration (fig. 8). [. . . ] Take into account dead or broken branches that may break off during felling creating a further danger risk. During tree felling operations in critical conditions, always remove ear protection immediately after cutting operations to be able to listen for unusual noises and any warning signals. Eliminate any branches that interfere with the job (fig. 8), starting from top to bottom, and then, always keeping the trunk between the user and the machine eliminate the more difficult branches afterwards, piece by piece. Eliminate all plants that interfere with work operations and control the area for possible obstacles (rocks, roots, ditches, etc. ) when planning the retreat path (to follow during tree fall); Refer to the illustration (fig. 9) for the directions to be maintained (A. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX ETN1062




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX ETN1062 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.