User manual AEG-ELECTROLUX ESF65012

[. . . ] Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Always insist on genuine spare parts. Disposal Dispose of the dishwasher packaging material correctly. Plastic parts are marked with standard international abbreviations: >PE< for polyethylene, e. g. Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling. [. . . ] - Soften remnants of burnt food in pans For washing in the dishwasher the following cutlery/dishes are not suitable: Cutlery with wooden, horn, china or mother-of-pearl handles - Plastic items that are not heat resistant - Older cutlery with glued parts that is not temperature resistant - Bonded cutlery items or dishes - Pewter or copper items - Lead crystal glass - Steel items subject to rusting - Wooden platters - Items made from synthetic fibres are of limited suitability: - Only wash stoneware in the dishwasher if it is specifically marked as being dishwasher-safe by the manufacturer. - Glazed patterns may fade if machine washed frequently - Silver and aluminium parts have a tendency to discolour during washing. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use. - Some types of glass can become dull after a large number of washes Open the door and slide out the baskets to load the dishes. The cutlery basket Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Cutlery should be placed in the removable cutlery basket with the handles facing downwards. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Move the front runner stops (A) of the upper basket outwards and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. DE02 RC01 After loading your machine always close the door, as an open door can be a hazard. 8 Use of "3 in 1" combi detergent tablets General advice These products are tablets with combined detergent/rinse-aid and salt functions. Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers (on the product packaging). 15 minutes, with the door ajar, after the end of programme so that they dry better and will be cooler. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off. 5. Interrupting a washing programme Interrupt a washing programme in progress ONLY if it's absolutely necessary Attention!Close the door; the programme will start from the point in which it was interrupted. Press the On/Off push button (in this case the On/Off indicator light turns off) Press the On/Off push button again; the programme will start from the point in which it was interrupted. 10 Maintenance and cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc. . . . ). Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run a 65°C wash programme without dishes using detergent. To ensure a correct working of the dishwasher, NEVER try to remove the upper spray arm. If residues of soil have clogged the holes in the upper spray arm, remove them with a toothpick. MA33 Cleaning the central filters (After each wash) Inspect the central filters (B) and (C) and remove any scraps of food with a brush, under running water. [. . . ] If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. For making the connection itself, the coupling nut fitted to the machine's supply hose is designed to screw onto either a 3/4" inch gas thread spout, or to a purpose made quick-coupling tap such as the Press-block. Fitting under a counter (kitchen worktop or sink) By removing the machine's worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture. 570600 450 IN04 Proceed as follows: Remove the machine's worktop by unscrewing the two front retaining screws, pull from the front and slide out the rear slots, lifting the worktop. Insert the machine after adjusting height and levelling with the adjustable feet. When inserting the machine, ensure that the water inlet and drain hoses are not kinked or squashed. [. . . ]