User manual AEG-ELECTROLUX EFC9750X

[. . . ] Moreover, it is not permitted to connect the scavenging pipe for fumes in other adjacent rooms or wellholes, or pipes for fire-fighting devices. In any case it is necessary to respect all norms concerning scavenging of the air. Any user who does not adhere to these instructions is risking his own life and the lives of others. 4) If the hood is used as a suction hood, it is necessary to guarantee enough airexchange for instance making a hole for ventilation on the outside wall by qualified personnel. [. . . ] For safe ventilation, maximum depression in the room should not exceed 4 Pa (0, 04 mbar) and there must be a hole on the outside facing wall (suitably positioned and dimensioned); never use the hood without the grease filters; keep the grease filters clean, taking into account the recommended cleaning suggestions; replace the carbon filters (if the hood is used as a filtering hood), as indicated; turn on the hood motor before you start cooking; turn off the hood motor about 10 minutes after you have finished cooking; do not use the hood to suction gas, fumes, vapours or other substances different from the normal fumes in the kitchen. 9b: soft touch control with led points and push buttons screenprinted on s/steel; see par. 9a) The activated functions are listed as follows: LIGHTS: to switch the lights on or off; (pressure inf. To 1 second); MOTOR OFF: turn the motor off; TIMER: if pressed when the hood is already functioning with one of the pre-established speeds, timing is activated, that is a count down of 15 minutes, after which the motor stops. During this time the display indicates the speed number and the point led flashes; reduces the speed of the motor; increases the speed of the motor; INTENSIVE SPEED: the intensive speed is the highest motor speed. It is automatically excluded after 5 minutes and the hood goes rd back to the 2 speed. Only in case of filtering hood (flashing C letter) carbon filters should be replaced or regenerated. 2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTERS The electronic controls with display allow automatic control of the grease filters and the carbon filters (only when the hood is used in the filtering version), so that the user does not have to remember when maintenance was last carried out. When the metallic grease filters have to be cleaned, the letter F on the display will flash. When the carbon filters have to be replaced, the letter C on the display will flash. It is possible to consult the electronic system concerning how clean the grease filters are and how worn the carbon filters are, as follows: stop the motor and . To find out how clean the fat filters are, press the O and - buttons at the same time. On the display, a number between 0 and 9 will appear, the smaller the number, the dirtier the filter is; . To find out how worn the carbon filters are, press the buttons O and +. On the display, a number between 0 and 9 will appear, the smaller the number, the more worn the filter is. Push the push-buttons 0 (zero) and T (timer) at the same time for a few seconds. 4 SETTING THE SUCTION /FILTERING USE OF THE HOOD The hood is delivered standard for suction use (only with flashing F letter). If you wish to use it in the filtering version (F and C flashing) proceed as follows: and T on the display for about 5 seconds, the following symbol will press the buttons appear followed by a 0. At each pressure of the Light Button, it is possible to change the value shown from the O (suction function), to 1 (filtering function) and viceversa. To activate the functions connected to these push buttons, it is necessary to apply a little pressure just lightly and for a short time. If pressure is too lengthy on the push buttons the connected functions are not activated. The functions activated by the push buttons are as follows: LIGHTS: switch the lights on and off; TIMER: if pressed when the hood is already functioning with 1st, 2nd, 3rd or 4th speed, the led point connected with the selected speed, starts to flash for 10 minutes, after which motor automatically stops. [. . . ] The manufacturer will not be responsible for any damages either functional or to the appearance of the hood, caused by cleaning operations carried out using unsuitable products or unsuitable methods. The following optional accesories are available and are sold separately: · If the cooker hood is not responding to the controlS, disconnect electricity for about 1 minute, taking the plug out or disconnecting the main electricity supply, then reconnect. This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This norm is the frame of a European-wide validity of return and recycling of Waste Electrical and Electronic Equipment. [. . . ]